HP DesignJet 8000
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
If the paper does not load, the leading edge of the paper may not be straight or clean and needs to be trimmed. Remove the initial 2 cm (1 in) from the roll and try again. This may be necessary even with a new roll of paper. Ensure the roll ends are tight against the spindle ends.
A 05:10 error on the front panel of the printer indicates a formatter card failure. This issue usually does not require on-site service, as the formatter card is a user-replaceable part. It is a simple fix. The card is located on the back side nearest the power cable plug.
NOTE: The Designjet 510 and Designjet 800 WILL NOT be able to completely boot up without the card, it will show a message saying WARNING 05:10 (notice that this time it is a warning, not the actual System Error). Once it shows the warning please press the ENTER button. This will allow the printer to get to ready mode.
the error indicates that is not read correctly progress paper. this may be for several factors. 1- encoder disk erase, rush etc. 2- paper roll heavy, block, stopped.
System Error 79.02:04 appears while the printer is idle or when booting. The issue is caused because the printer is trying to access an HP URL that is no longer valid. 3.
Generally, System Error 86:01 refers to paper jams or obstructions (problems moving the carriage) in the Scan Axis area.
System Error 11:11 – What does it mean? Error 11:11 is normally displayed on the front panel of your HP Designjet Printer because a fault has been detected with the trailing cable. The trailing cable is the component that provides communication between the printer electronics and the carriage PCA.
The more likley fault is the carriage board. The board is now removeable – so just reverse the whole process one this is done and boot the printer. You can check if the fault is cleared by booting once all the cables are in place – you dont need to re asseble the whole machine.
59.10 is a main drive error, which could be a bound up fuser. 51.10 is a laser error, which could be a bad laser unit. Which error do you have? If the printer can print an engine test, then you may have a bad formatter.
23 or 30.03. 45 Scanner Errors. The resolution for either error is to, if preferred to send a firmware update, then replace the flatbed scanner assembly. It has been found that it is in most cases the internal lamp that has failed, but is not available through HP as a replaceable part.
There are numerous possible causes for a printer that`s randomly producing blanks. The most common ones are empty ink cartridges, improper cartridge installation, and congested nozzles. Driver and software issues can sometimes cause this problem as well.
Open your image in Adobe Acrobat. Select `Print` from the tool bar or by key command. On the print dialogue window do the following: For the Printer, select “HP Designjet T120”.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr
Read Full Q/A … :
HP DesignJet 8000
HP 26 vs HP 29 cartridge compatibility
ANSWER : Eu decidi fazer um binário opções, o primeiro passo neste trabalho yavlyaetsya formação inicial e os fundamentos .. Put Options and Call Options Trading É por isso que eu escolhi um par de artigos de alguns sites na Internet, se você pode se perguntar vospolzovatsya put-call-options.com/br/what-are-options/binary-options-and-strategies
Read Full Q/A … :
HP DesignJet 8000
HP 4250 13.06.00 Fuser output paper stop !
ANSWER : pick up solenoid
Read Full Q/A … :
HP DesignJet 8000
HP 4250n – blurry text
ANSWER : What is the fuser? And how can it be changed?
Read Full Q/A … :
HP DesignJet 8000
HP 4101MFP Hard Drive Question
ANSWER : To initialize: turn off – Press start and hold down while turning on, release after all three light light, you should see initialize disk hit check, and allow to boot.
Read Full Q/A … :
HP DesignJet 8000
HP 9040 MFP Error code
ANSWER : bonsoir
Read Full Q/A … :
HP DesignJet 8000
HP 4550N formatter board
ANSWER : You can replace it by finding the slot of DIMM, where the existing HP4550N formatter board is installed. More info is available here
Read Full Q/A … :
HP DesignJet 8000
Reseting the ink levels for hp c7280,
ANSWER : I held the # and 6 down long enough to start a complete re-set of the printer But the Black ink level still shows as depleted when it is actually still half full.
Read Full Q/A … :
HP DesignJet 8000