HP DesignJet 8000

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

An HP ink system error can also be caused by low or empty ink or toner cartridges. If you spot an “Ink System Failure” message before discovering the error, then replace the ink or toner cartridge to resolve the problem.
Select a printer, and, at the top of the window, click Print server properties. From the Advanced tab, check or uncheck Show informational notifications for local printers and Show informational notifications for network printers. Click OK.
When the low ink warning appears, press and hold the STOP/RESET or RESUME button on the printer for 10 seconds. This button will flash with an orange light when the warning pops up, so it will be relatively easy to find.
– (1) Remove the ink cartridge from the printer. (2) Power OFF the printer for 2 minutes. (3) Power ON the printer and re-install the ink cartridge(s). (4) Run the head cleaning cycle.
If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.
Clean the Cartridge Contacts: one of the most common reasons you might get a cartridge problem error when your cartridges are new and full is the contacts on the cartridge might be dirty or otherwise obscured from making good contact with the electronics in the printer head carriage.
The title, ink system failure, or printhead error code 0xc19a0003 means that the problem associated with the ink cartridge. Consequently, there are two instances either ink cartridge not providing ink well or, it may be confused by the printer.
I`d recommend starting by removing the ink cartridges, and performing a power reset. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Printer toner Cartridge for an HP 3600DN
ANSWER : You need to replace the chip to reset the count. http://www.aliexpress.com/cp/hp-3600dn-toner-online-shopping.html

Read Full Q/A … :

HP DesignJet 8000

HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr

Read Full Q/A … :

HP DesignJet 8000

All panel lights blinking, printer doesnt respond
ANSWER : This is very easy process, you must change a new one

Read Full Q/A … :

HP DesignJet 8000

HP Laserjet printer page counter backward move
ANSWER : On all HP laserjet printers if you power them off the page count will decrease back to the nearest 10. For example, if the page reading is 123,799 and you power it off, the page count will go back to 123,790.

Read Full Q/A … :

HP DesignJet 8000

Printer stops pulling paper from tray 2 after a few sheets
ANSWER : Sticking pickup roller solenoid. Pretty easy fix. You need to remove the right side covers. The back one just slides off, but the top holds the front one. I usually just take the 2 right side screws off and gently lift the top enough to pop off the side panel. Open the metal door on the formatter assy. Then release the tab in the middle. There’s also a tab at the front of the panel. When putting it back on, make sure you engage the rocker switch and the metal rod before pushing it into place. When you get it open, you’ll see the solenoid at the bottom front. There’s 1 screw holding it in place. Remove it and take the top plate and spring off. Be careful not to lose the spring. Then scrape off the gooey crap on top and clean off the plate as well. I put a piece of thin sticky backed felt in place of the remnants of the disintegrating sponge that HP uses. You can find it at the hardware store used for the bottom of chair legs.

Read Full Q/A … :

HP DesignJet 8000

newly installed printer…can scan but cant be set as a default printer???
ANSWER : ITS AN EPSON L210…

Read Full Q/A … :

HP DesignJet 8000

HP 4250 13.06.00 Fuser output paper stop !
ANSWER : pick up solenoid

Read Full Q/A … :

HP DesignJet 8000

Difference Between Laser Printer and InkJet Printer
ANSWER : Laser uses toner which is a powder that gets melted onto the page. Inkjet uses ink that gets squirted onto the page.

Read Full Q/A … :

HP DesignJet 8000