HP DeskJet 5650

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

The encoder strip is a thin, clear plastic strip located on the printer`s platen. It helps the printer determine where the printhead is located and how much ink to eject. Over time, the encoder strip can become dirty and covered in ink. This can cause printing problems and affect the quality of your prints.
On your PC search control panel, open control panel, Select printer properties, Select the “number of copies” it must be set to 2 change it to 1 and check if it helps. If the issue still persists uninstall the printer software from your PC and install the latest printer drivers.
Open the document, and then click File > Print. Select your printer, and then click Printer Properties, Preferences, or Printer Setup. From the print settings, select the option for a two-sided print job.
The encoder strip is a clear plastic strip with small timing marks printed on it, which tell the printer where the print head is located along the horizontal print head path. If it becomes coated with ink, it can interrupt printing activity.
The Encoder Strip is the semi-clear strip located just above the carriage slider rod. Its purpose is to help the print carriage accurately keep track of its position as it moves along the carriage rod.
Doubling is a register problem that mainly occurs between plate and blanket within the unit. Too much blanket to paper pressure. Reduce printing pressure to a minimum. Too much plate to blanket pressure.
The best way to locate the encoder strip is to look on the left side of your machine in the opening between the platen and the support arm. There you will see two plastic strips running the width of the machine. One gray and the other clear. The gray strip is the encoder strip.
Clean the device

You should avoid using any harsh chemicals, solvents, or abrasives that could damage the device or leave residues. For optical encoders, you should also clean the lens and the disk with a lint-free cloth and a mild cleaner.

Change Print Settings Windows

Select the printer you`d like to use, and select the Properties button. Under the Layout tab, you can choose the method you want under the Print on Both Sides section. By choosing None, the document will print single-sided.

OBS Studio is an open-source software encoder for live streaming. OBS Studio is a great option for those new to live streaming as it`s effortless. It`s also been hailed as the best encoder for YouTube out there. OBS Studio`s broadcasting software offers Windows, Mac, and Linux downloads.
Encoders are used in devices that need to operate in high speed and with high accuracy. The method of controlling the motor rotation by detecting the motor rotation speed and rotation angle using an encoder is called feedback control (closed loop method).
Encoder is a device designed to convert the motion of the shaft into a digital code. The device is connected to the printer to monitor the line`s speed. The Encoder can be mounted on different areas depending on the type of production line or the product.
Polycarbonate type (Transmissive/Reflective)
Dirty or misaligned print heads

Your printer may be printing fuzzy, blurry, or other faint text because of dirty print heads. All modern printers have a self-cleaning mode, which cleans the print heads, and additional internal equipment used in the printing process.

: to produce two images from two negatives in a fixed position on (a photoengraving plate)
To test encoder outputs with a multimeter, you need to set the multimeter to the appropriate mode and range, depending on the signal type and level of the encoder. For single-ended and differential signals, you can use the DC voltage mode and connect the multimeter probes to the channel wire and the ground wire.
An encoder converts your video into a digital format to stream on YouTube. Some encoders are software apps on your computer, while others are standalone hardware.
Use the zero pen to set the encoder zero position (see image): 3.1 Touch the Zero mark with the apex of the Zero pen – the status LED goes off. 3.2 Hold the Zero pen for 3 seconds. 3.3 The new Zero position is set when status LED goes RED.
An encoder is classified into four types: mechanical, optical, magnetic, and electromagnetic induction types.
The good news is that most encoder problems are economically repairable by an experienced industrial electronics repair center.
The most common cause of encoder failure is a warped/ bent shaft that is no longer sitting on the bearings properly, an issue also referred to as shaft run-out. A warped shaft adds stress to the internal bearings and may lead to bearing failure and eventual overheating of the encoder.
Assuming that the driver is defaulted to duplex, you change as follows. On your PC go to control panel >devices and printers and right click on the icon for your printer and select printer properties from the drop down menu. Click the advance tab and select default settings and change to single sided.
Partial prints are a common issue with printers and there are several main reasons it can occur: Problem with the print spooler (on Windows PCs) Overload of the GPU on later model Macs. Dodgy USB cord.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?

Read Full Q/A … :

HP DeskJet 5650

HP DeskJet 1220C Prints only Pink & Black
ANSWER : hi everyone. i have an hp ink advantage 5525 all-in-one. changed all cartridges as they were empty and when i tried to print i got blank pages. i gave a print order a couple times to find out what was going on and found out that yellow and magenta inks worked but not cyan and black. removed cartridges, clean and all many times and nothing happened. then i tried this youtu.be/f57jOGj-G5s and the print quality of magenta and yellow improved significantly but still no black or cyan at all. i can’t do the running water thing because the print head is not detachable. any suggestions?

Read Full Q/A … :

HP DeskJet 5650

HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr

Read Full Q/A … :

HP DeskJet 5650

I just bought an officejet 3830 2 weeks ago. Now it won't print at all! Says inkjet jam. It's not! I've done all the fixes as per hp's website now what?
ANSWER : Take it back and exchange it under warranty.

Read Full Q/A … :

HP DeskJet 5650

Help the cover on the back of my printer is lost and my printer keeps on shooting out paper from the back end with no writing on it?
ANSWER : There are no parts available, therefore no solution to your problem.

Read Full Q/A … :

HP DeskJet 5650

HP LaserJet 2200D won't print configuration page
ANSWER : Find someone with a HP LaserJet 4100 and you can configure the card to the IP you want:

Read Full Q/A … :

HP DeskJet 5650

HP Deskjet 640c wont print??
ANSWER : yes

Read Full Q/A … :

HP DeskJet 5650

hp deskjet 960c printing problem
ANSWER : RE: HP 960c printer. I have new cartridges and the test page prints out full color. When printing a color document the page prints in black & white. Why not color? The print page is on color not black & white.

Read Full Q/A … :

HP DeskJet 5650