HP CopyJet M
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
50.2 error indicates that the printer is not heating up fast enough. This can be caused by a bad heating element in the fuser but can also be caused when the printer does not have adequate power due to overloaded circuits or being plugged into a power strip or surge bar that limits current flow.
The message “Fuser Kit Low” or “Fuser Kit Very Low” on your HP Color LaserJet M553 series printer is a warning that you have reached the recommended number of prints for your fuser assembly. (The fuser assembly is the consumable part in your printer which heats up and bonds toner to the paper.
Streaking, smudging, black lines, and double images are all symptoms of a bad fuser. When you notice these printing defects and experience problems, such as paper jams or wrinkles, this is a good sign to replace the fuser kit.
If you see this error code 50.5 on an HP LaserJet 4200, 4240, 4250, 4300, or 4350 series printer, the fuser installed in the printer is registering as an incorrect fuser for that model printer.
The flag located right of the pick-up roller has a fixed position. If the flag becomes stuck or broken, it will produce a 60.02 tray lift error or a “LOAD PAPER” message. If this flag is broken or if the sensor has failed, the RM2-6368 paper feed guide will need to be replaced.
Error code 59.40 for HP Laserjet 4350 means that your printer has a print cartridge motor error.
Fuser Unit – 120 Volt Compatible with HP LaserJet 5200dtn (A0182)
Look inside the fuser opening to make sure there is no debris or jammed paper. Remove any debris or jammed paper, if found. Hold the handles on each side of the fuser and reinstall it in the printer.
In this case, it is recommended that you replace the fuser unit with a new one. The life of the fuser unit when printing A4 size paper is approximately 50,000 pages.
Most laser printers will inform you when the fuser unit needs to be replaced. An easy way to identify when a fuser unit needs to be replaced is when smudging or smearing on your printout begins. Smudging and smearing occur when the fuser stops heating the toner particles enough to melt them onto the page fully.
Push up on the release buttons on both sides of the fuser to release the springs, and then pull the fuser out of the printer. Place the old fuser aside for recycling. Remove the new fuser from its box. Remove the protective packaging.
The fuser unit or fuser is a critical part of any laser printer. Using pressure and heat, it fuses the toner powder onto the page to create a print, and without it, the printer cannot operate.
Push up on the release buttons on both sides of the fuser to release the springs, and then pull the fuser out of the printer. Place the old fuser aside for recycling. Remove the new fuser from its box. Remove the protective packaging.
The fuser unit or fuser is a critical part of any laser printer. Using pressure and heat, it fuses the toner powder onto the page to create a print, and without it, the printer cannot operate.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
HP 4250 13.06.00 Fuser output paper stop !
ANSWER : pick up solenoid
Read Full Q/A … :
HP CopyJet M
HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:
Read Full Q/A … :
HP CopyJet M
HP LJ 4350 – Tray 2 not lifting, no motors turn.
ANSWER : I can’t believe, pieces of paper was under the registration flap, now my 4250N is working.
Read Full Q/A … :
HP CopyJet M
Service manual for an HP Laserjet 4250 (or 4250n)
ANSWER : Hello all,Can someone please tell me where to find service manual for a 4250 or 4250n printer?I used Google, Fileshare.eshop.bg, peer-to-peer, but with no avail …Thanks alot for your answers!
Read Full Q/A … :
HP CopyJet M
HP Laser Jet 4250 13.01.00 Jam in Tray 2
ANSWER : did you check if there’s multiple feeding while pulling papers
Read Full Q/A … :
HP CopyJet M
HP 4250, error 54.1 Remove sealing tape from toner
ANSWER : I am having the same problem as everyone else can someone send me a new link or the pdf
Read Full Q/A … :
HP CopyJet M
Laserjet 4250 print quality issue (see image)
ANSWER : It looks like a fuser problem. One way to prove it is with the half-stop test. Put a sheet in the drop down manual feed tray. Send a print job and watch the paper. When the end of it is about to enter the printer, open the lid and take out the toner cartridge. Look at the printed image. If it looks OK, then it is a fuser problem. If not, then it is a toner cartridge issue since it hasn’t gone through the fuser.
Read Full Q/A … :
HP CopyJet M
HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply
Read Full Q/A … :
HP CopyJet M