HP LaserJet 4

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Sometimes a paper jam error persists even though there is no jammed paper (false paper jam). Reset the printer, which might clear a false paper jam error, and then try to print again. With the printer turned on, disconnect the power cord from the printer. Unplug the power cord from the power source.
With the printer turned on, disconnect the power cord from the rear of the printer and also unplug the power cord from the wall outlet. Remove USB cable, if present. Wait for 2-3 minutes, press and hold the power button on your printer for about 30 seconds to remove any additional charge.
From the control panel go to : setup menu>printer maintenance and then select either cold reset or factory reset.
Sometimes a paper jam error persists even though there is no jammed paper (false paper jam). Reset the printer, which might clear a false paper jam error, and then try to print again. With the printer turned on, disconnect the power cord from the printer. Unplug the power cord from the power source.
Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Clean the rollers inside the printer, and then try to print again. Turn off the printer, and then disconnect the power cord.
Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Clean the rollers inside the printer, and then try to print again.
A piece of paper stuck in the paper tray or inside the printer can create a paper jam. Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer.
A paper jam is when paper or other printed material gets stuck or lodged in a printer and cannot eject.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
Turn the printer off then back on. If the issue persists, turn the printer off, unplug the power cord and then wait at least three minutes before plugging the power cord back in and turning the printer back on. If the issue persists, ensure the product is running the latest firmware available from HP.com.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :

HP LaserJet 4

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :

HP LaserJet 4

paper jam
ANSWER : If you remove the fuser (2 screws), look to the left and you’ll see a gear on a metal bracket. That’s the coupling gear. It drives the fuser. You’ll see that it is yellow with teeth missing. You’ll need to replace it. You have to take the formatter assy. to the left of it off, and then there are a few screws holding it in place.

Read Full Q/A … :

HP LaserJet 4

Paper Jam 13
ANSWER : Sticky paper pickup solenoid. Since MF tray doesn’t use it, it works fine. Solenoid is located on right side of printer at the end of the paper pickup roller shaft. You need to remove the solenoid, take the plate and spring off the top and then scrape off the gooey residue that’s causing it to stick. Then you get a thin piece of sticky backed felt and put it on top of the metal base. You can find some at the local hardware store, they’re used on the bottom of chair legs.

Read Full Q/A … :

HP LaserJet 4

LaserJet 4 won't Power Up
ANSWER : I haven’t seen that particular behavior on that model. It either works or it doesn’t. My first choice would be the power supply.

Read Full Q/A … :

HP LaserJet 4

I just bought an officejet 3830 2 weeks ago. Now it won't print at all! Says inkjet jam. It's not! I've done all the fixes as per hp's website now what?
ANSWER : Take it back and exchange it under warranty.

Read Full Q/A … :

HP LaserJet 4

HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr

Read Full Q/A … :

HP LaserJet 4

Keep getting a paper jam message. There is no jam.
ANSWER : You can quit wondering. Parts are unavailable. I’ve seen posts where people have 3D printed the parts or machined them out of metal.

Read Full Q/A … :

HP LaserJet 4