hp 3500 - 59.99 error

HP Color LaserJet 3500

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

59 error could be a bad motor or Developer motor rotation error. Remove all toner, power cycle the printer, and re-install one at a time, closing the access door each time before inserting another. See if one of the supplies seems to trigger the error.

This is a main motor startup error. In other words when the motor is supposed to turn it can not and gives the error.

Description: Printer boots up to 59. F0 Error and is unable to print. This error is primarily caused by one of the following conditions: A transfer alienation failure in which the ITB is stuck and unable to properly engage the internal transfer rollers.

59 error including loud noise followed with a poor print quality and toner cartridge coming out of its position, and/or toner access door starts to open by itself. Source of all above-mentioned symptoms is a bent metal ( U shaped) shaft that is used to lock toner cartridge in position for printing.

The HP printer error 59. F0 may be caused due to the failure in transfer alienation. Transfer alienation is a situation in which the Intermediate Transfer Belt (ITB) gets stuck and does not fully rotate. Another possible reason for the error 59.

Error 59: The Network is Down, Unreachable, or Has Been Reset.

59.10 is a main drive error, which could be a bound up fuser. 51.10 is a laser error, which could be a bad laser unit. Which error do you have? If the printer can print an engine test, then you may have a bad formatter.

The drive system the motor drives may be too tight causing an over current state in the motor. Use the feed motor (M101) drive test in the Component test to verify that the motor is not working.

59.70 error is a black developer motor error. It can be caused by a faulty black cartridge or power starvation that results if you have the printer plugged into a surge protector or UPS unit.

This is a ITB motor rotation error. Take out the ITB (Intermediate Transfer Belt) and check it for any damage. Re-install it back in the printer and try again. If the error persists, then the printer must be serviced.

60 Black drum motor rotation abnormality.

A 59.00. B0 Cleaning motor error is displayed on the control panel when there is a problem with the cleaning motor. The motor might be stalled due to the toner collection unit (TCU) being full, the waste toner chute is clogged, or the cleaning motor is stalled.

This error is specifically related to the fuser drive motor itself. The manual states that it`s a “fuser motor start up error“.

The 59.05 errors are related to main motor and toner cartridge. In many cases the drum unit in the cartridge does not rotate and replacing the defective cartridge will resolve the error. You can test the motor by going to diagnostics and running the motor test without a cartridge installed.

The 59. F0 error is typically the result of a small sensor switch inside the ITB (Intermediate Transfer Belt) assembly that is not working correctly. It will have variable amounts of resistance as it is activated during the course of operation and causes the error.

59.70 error is a black developer motor error. It can be caused by a faulty black cartridge or power starvation that results if you have the printer plugged into a surge protector or UPS unit.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP 3500 59.99 error

ANSWER : (Trying again, this website thinks return means end of comment)

Read Full Q/A … :

HP Color LaserJet 3500

HP laser jet 3015 "Upgrade Error Call HP Support"

ANSWER : rgtr

Read Full Q/A … :

HP Color LaserJet 3500

HP Color Laserjet 500 series M551n Error 98.00.0C

ANSWER : I just ran into one of these on a 4 year old m551. Failed to complete startup at the end of disk check. Followed the above link for troubleshooting.

Read Full Q/A … :

HP Color LaserJet 3500

HP 4050 Error 13.1 & 13.20

ANSWER : I tried the fix you recommended but it still would not fix.

Read Full Q/A … :

HP Color LaserJet 3500

Error Code 51.1 says Printer Error No Kidding.lol

ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :

HP Color LaserJet 3500

HP Laserjet 4250 – RFU LOAD ERROR

ANSWER : Italiano:

Read Full Q/A … :

HP Color LaserJet 3500

HP 9040 MFP Error code

ANSWER : bonsoir

Read Full Q/A … :

HP Color LaserJet 3500

HP Laserjet 4200 50.2 Fuser error

ANSWER : if you are using a good fuser the next part to try would be low voltage power supply