HP Color LaserJet 2500

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Check for obstructions in the carriage path

Open the cartridge access door to get to the carriage inside the printer. Make sure the carriage is not obstructed by gently sliding the carriage side to side. Look for and remove any obstructions in the carriage path, such as crumpled paper or dislodged labels.

An E2 error occurs when the printer attempts to print a single-page or multi-page print job, and the paper length selected in the print settings does not match the length of the loaded paper.
The 24 character error code is a failure of the short Disk Self Test ( DST ) and would indicate that the Hard Drive is failing and needs to be replaced. Hi, It means the hard drive has failed the quick test and needs to be replaced.
There is a communication failure with the imaging drum. Turn the printer off and then on. If the error persists, replace the imaging drum. If the error still persists, contact HP. 10.000X Supply memory error or 10.100X Supply memory error.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
An Er/04, Er/05, or Er/06 error message indicates a paper jam. Find and clear the printer of any jammed paper, or reset the printer if the printer has no jammed paper.
The F5 E3 alert indicates there is issue with the lid lock. Do not force the lid open, as permanent damage could occur. Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid.
That error code translates to a tray 2 feed where the paper was detected as too long or too short. As tray 1 prints fine, you can rule out any sensor in the path that the manual feed takes.
The F6 E2 alert indicates there is issue with the appliance control unit, user interface or associated wiring. Unplug the washer, wait five minutes, then plug back in.
The E1 error code is an AUTO-STOP PROTECTION indicating a short or open circuit in the indoor pipe sensor. Try unplugging the unit and waiting 2 minutes for the power to discharge. Then plug the unit back in. The E2 error code is an AUTO-STOP PROTECTION indicating a short or open circuit in the indoor pipe sensor.
a misprint or misspelling in a text.
1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.
While trying to use SSH, you may get a response indicating permission is denied. Or if you get an error with a code of 255, it means there`s a problem with your SSH connection.
The “Wrong Cartridge Type/Installed” / “Print cartridge is not compatible with this device” / “Cartridge Error” / “Print Cartridge Error” / `blinking lights” alert/error message is typically indicative of failed micro-electronics internal to the ink cartridge(s).
An E1 or E2 error indicates that the paper size setting does not match the paper size that is loaded.
25: The laser/scanner unit motor is stopped, but the ready signal indicates that the laser/scanner unit motor is operating. 63.00. 26: The laser/scanner unit motor is operating, but the ready signal for the laser/scanner unit motor does not change. 63.00.
What does error 0x80070005 mean? Windows update error 0x8007005 indicates that the system user lacks permissions or the system update does not contain critical files needed to install the update.
A 42 or Toner Cartridge Region Mismatch error indicates that the installed toner cartridge is manufactured for a different geographic region than the printer. The printer and the toner cartridge each have a certain geographical code tagged to them, much like the coding on DVD players and DVDs.
To clear the error manually push the UP, DOWN and PUMP buttons simultaneously, ensure the display clears before showing the temperature or error code again. If the display does not clear the reset was not executed correctly.
An E0 error indicates an unusable cartridge. This condition occurs when at least one ink cartridge needs attention, is faulty, incorrect, missing, damaged, or incompatible. Reseat both ink cartridges, clean the ink cartridge contacts, restart the printer, and replace one or both ink cartridges if necessary.
Did you receive a F5 E2 lid lock alert? The F5 E2 alert indicates the washer can`t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area.
The water in the reservoir is not being sensed correctly. There may be a problem with the Conductivity Sensor, or the associated wiring.
There may be a problem with the Oven Door Latch Assembly, the Door Switch, or the associated wiring. Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Monitor the oven for one (1) minute to ensure the error code does not display again.
The F5 E2 alert indicates the washer can`t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP 9040 MFP Error code
ANSWER : bonsoir

Read Full Q/A … :

HP Color LaserJet 2500

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :

HP Color LaserJet 2500

HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr

Read Full Q/A … :

HP Color LaserJet 2500

Hp designjet 500 error code 11:11
ANSWER : I have an HP designjet 510 I just powered it on and it only shows error 11:11. does anybody have a solution?

Read Full Q/A … :

HP Color LaserJet 2500

Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.

Read Full Q/A … :

HP Color LaserJet 2500

HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:

Read Full Q/A … :

HP Color LaserJet 2500

HP 4050 Error 13.1 & 13.20
ANSWER : I tried the fix you recommended but it still would not fix.

Read Full Q/A … :

HP Color LaserJet 2500

HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply

Read Full Q/A … :

HP Color LaserJet 2500