HP LaserJet 2100

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

The printer is either low in toner, the density is set too low, or the Economode may be turned on. Remove the toner cartridge and shake it. This will redistribute the toner and often will temporarily solve the problem. However, this usually indicates it is time to install a new cartridge.
You need to ensure your HP printer has enough paper, ink, or toner, and it is not stuck on paper jam. Also, check the status of your printer cartridge and try replacing it with a new one if it is not good enough. In some cases, your HP printer stops printing after you replace its parts.
To initiate a hard-reset, turn the printer off and then on again whilst holding down the cancel and go buttons until all the lights show solid.
The Power button is blinking. This condition might be caused by an open ink cartridge access door, an empty input tray, a paper jam, or a carriage jam. An error message might display on your computer. If a `paper jam` error message displays on your computer, try the steps to clear the paper jam.
Select Start , then select Settings > Devices > Printers & scanners . Scroll down to Related Settings and select Print server properties. Select the Drivers tab, and see if your printer is listed. If it is, you`re all set.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.
Reset. Resetting the printer stops printing and clears the current print job received from the active interface. You may want to reset the printer when there is a problem with the print job itself and the printer cannot print successfully.
If your printer is running low on ink, it may start printing blank pages. To check your ink levels, go to your printer`s control panel and select the Ink Levels option. Whenever the ink levels are low, replace the cartridges with new ones. You can also try shaking the cartridge gently to redistribute the ink.
Several factors may cause the product to print blank pages, such as print settings, low ink, or the product itself. Check the following: Make sure the product is placed on a flat, stable surface that extends beyond the base in all directions. The product won`t operate properly if it`s tilted or at an angle.
The paper might not be engaged with the feed rollers. The paper-width guide is pressed against the paper stack too tightly. The paper tray is not completely inserted into the product. The paper settings in the print driver do not match the paper loaded in the paper tray.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP LaserJet 2200D won't print configuration page
ANSWER : Find someone with a HP LaserJet 4100 and you can configure the card to the IP you want:

Read Full Q/A … :

HP LaserJet 2100

hp deskjet 960c printing problem
ANSWER : RE: HP 960c printer. I have new cartridges and the test page prints out full color. When printing a color document the page prints in black & white. Why not color? The print page is on color not black & white.

Read Full Q/A … :

HP LaserJet 2100

HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr

Read Full Q/A … :

HP LaserJet 2100

I just bought an officejet 3830 2 weeks ago. Now it won't print at all! Says inkjet jam. It's not! I've done all the fixes as per hp's website now what?
ANSWER : Take it back and exchange it under warranty.

Read Full Q/A … :

HP LaserJet 2100

Print file sent but no printing occurs
ANSWER : Been working on these since they first were released. Never seen a problem like yours. If it happens again, try doing an engine test, as it bypasses the formatter board. The engine test is located at the right side of the manual tray opening. Look for a hole in the side wall. Stick something like a paper clip into it to actuate the test button. It will then print a lined test page. If it does that, then it points to the formatter board as the cause of your problem.

Read Full Q/A … :

HP LaserJet 2100

HP DeskJet 1220C Prints only Pink & Black
ANSWER : hi everyone. i have an hp ink advantage 5525 all-in-one. changed all cartridges as they were empty and when i tried to print i got blank pages. i gave a print order a couple times to find out what was going on and found out that yellow and magenta inks worked but not cyan and black. removed cartridges, clean and all many times and nothing happened. then i tried this youtu.be/f57jOGj-G5s and the print quality of magenta and yellow improved significantly but still no black or cyan at all. i can’t do the running water thing because the print head is not detachable. any suggestions?

Read Full Q/A … :

HP LaserJet 2100

HP Deskjet 640c wont print??
ANSWER : yes

Read Full Q/A … :

HP LaserJet 2100

HP Officejet Pro L7680-problems w/black print head
ANSWER : VLCM Print tech supporters are very helpful to support printing related issues. They are industry certified technicians. they have 12+ years of handful experience. visit page – vlcmprint.com

Read Full Q/A … :

HP LaserJet 2100