HP LaserJet 2100

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

HP 2100 – To perform a cold reset, turn the printer power off, then press and hold the JOB CANCEL button. Turn the printer power back on and after all the LEDs come on release the JOB CANCEL button. A cold reset changes most system parameters in NVRAM to the factory defaults.
A 49 error typically occurs when the printer attempts to perform an action that the firmware is not capable of performing or might not be designed to handle, for example: Printing files that include unsupported printer commands. Interfacing with a third-party solution that was not designed to work with the printer.
Make sure your devices are properly connected with each other, and the network or the cable you use to connect these devices is normal. You can also try restarting your HP printer. Turn it off completely and unplug the power cord, leave it for a couple of minutes, and then plug the cord back and power on the printer.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
00 Page Too Complex. The printer displays this message to indicate that the page decompression process was too slow for the printer.
This 51.10 error code points to a failure with the laser scanner assembly, and to fix this error usually you end up replacing the laser scanner assembly. You can try turning the printer off and back on, which may temporarily reset the error and let you print a few more pages.
Common causes include dust and grime, worn rollers, or inappropriately weighted paper. Prevent paper jams by regularly cleaning your printer and replacing parts as needed. Check the weight of paper that your printer is rated for as well. The printed product is faded.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Answer. On HP printers, a “cold reset” causes the printer to return to its factory default settings, which among other things, causes it to try and retrieve its configuration information from a BOOTP server.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr

Read Full Q/A … :

HP LaserJet 2100

HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:

Read Full Q/A … :

HP LaserJet 2100

HP 4250n error 13.05.00 Phantom Jam
ANSWER : Pull and reset the fuser. Make sure both sides are back into their position.

Read Full Q/A … :

HP LaserJet 2100

HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply

Read Full Q/A … :

HP LaserJet 2100

HP 4050 Error 13.1 & 13.20
ANSWER : I tried the fix you recommended but it still would not fix.

Read Full Q/A … :

HP LaserJet 2100

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :

HP LaserJet 2100

HP 9040 MFP Error code
ANSWER : bonsoir

Read Full Q/A … :

HP LaserJet 2100

erro message (install genuine hp cartridge)
ANSWER : It seems like it might be a 4240 board. The 4240 was pretty much the same printer, but sold for $200 less. The downside is that it wouldn’t accept the 42X cartridges.

Read Full Q/A … :

HP LaserJet 2100