HP Color Inkjet 2000C

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

This condition occurs when paper is jammed inside the printer. To resolve the error, find and clear the printer of any jammed paper, or reset the printer if the printer has no jammed paper.
Status Indicator light glows solid red

The printer is in an error state. Disconnect the power cord or power bank from the printer, and then wait 30 seconds.

Status indicator light:

A blue or green light indicates the printer is operating correctly, while a red light indicates an error has occurred. A system error has occurred.

Battery Troubles:

If your HP laptop has a removable battery, remove it and reinsert it after a few seconds. Sometimes, a faulty connection can cause the power light to blink. If you can access a spare battery, try swapping it to see if the issue persists.

Some parts of the printer are broken, or there`s an internal error with the device. You need to restart your printer if you notice the `Resume` light and the Power light blinking together. There`s an improper connection. A flashing `Resume` light can also indicate a paper jam.
Ink in a cartridge is low. You can continue printing, or check which cartridge is low and replace it. An ink cartridge is expended or not installed correctly. Replace or reinstall the cartridge.
Faulty Display Settings

Improper display settings can also cause your computer screen to blink on and off. Your laptop`s screen flickers because the refresh rate, resolution, or color depth settings aren`t ideal. You can adjust the settings to see if it solves the issue.

Just above the circuit board on most printer cartridges, you`ll find a small button. You`ve seen these tiny buttons before on cell phones, phone chargers, etc. This is your reset button, and the only way to get in there is either with a paper clip or the tip of a pen (which will leave a tiny ink smudge on the button).
The Power light blinks fast when the ink cartridge door is open, or the printer is in an error state. If an error message displays on the computer or mobile device, follow any steps to resolve the issue. If the ink cartridge door is open, close it.
The Diagnostic LED blinks red 6 times and the system beeps 6 times (once per second), then a 2-second pause follows: This indicates a pre-video graphic card error. To resolve the issue, complete the following steps: 1) Reseat the graphics card.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Flashing Amber light
ANSWER : Make 1) check that the back of tray that is adjustable is against the paper and 2) the paper sensor for the tray moves freely – if it gets stuck it will cause that error.

Read Full Q/A … :

HP Color Inkjet 2000C

Flashing Lights & no display
ANSWER : Since it’s kind of old and there aren’t any parts available, you should probably go looking at replacement models. Saw a similar model (Canon) at Walmart’s this week that was wireless for $49.

Read Full Q/A … :

HP Color Inkjet 2000C

HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr

Read Full Q/A … :

HP Color Inkjet 2000C

My epson wf-3640 has two flashing blue lights going and will not print on command?
ANSWER : I think it is illicit anticompetitive behavior both quick essay service here in Australia and likely in different purviews too for them to look to cripple non specific ink use – and now it turns out it impairs their own particular ink and printer as well.

Read Full Q/A … :

HP Color Inkjet 2000C

HP 2200 – blinking attention light and tray 2
ANSWER : Nice day. (QUALITY IS OUR CULTURE)

Read Full Q/A … :

HP Color Inkjet 2000C

flashing printer lights
ANSWER : The contacts between the cartridges and the printer may need cleaning; the cartridges may be low but not out; or there could be a job stuck in the print que.

Read Full Q/A … :

HP Color Inkjet 2000C

Epson Stylus Photo R230 – flashing red lights fix
ANSWER : REDLIGHT

Read Full Q/A … :

HP Color Inkjet 2000C

HP 2200DN stopped with all 3 lights on
ANSWER : You need to press both buttons when you get the lights on. This will give you a secondary light code that tells you what is causing the failure.

Read Full Q/A … :

HP Color Inkjet 2000C