HP LaserJet 1200

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

This error might display if the fuser temperature becomes too hot. Follow these steps to turn off the printer and allow the fuser to cool before printing again. Press the Power button to turn off the printer. Disconnect the power cord from the rear of the printer.
The message `Fuser Error` or `Self-Diagnostic` means either the fuser has reached the maximum temperature allowed or there has been an error in detection of the correct temperature during specific times of the printing process.
If you have NOT recently replaced the fuser or heavily jostled the printer around, then the 50.7 Fuser error indicates you have an actual fuser failure (the gearing pressure is not releasing) and the fuser needs replacing.
The fuser unit is a vital component of laser printers. Most fusers last between 50,000 and 200,000 pages, depending on the design.
A fuser unit is a pair of heated rollers within the printer that fuses the toner onto the paper being printed on. Toner particles are pulled to the paper to create the desired text and images as the paper passes the imaging drum.
The Fuser is the piece that fixes the toner on the paper. This, like any other consumable part, wears out with the regular use of prints, since it is one of the components that suffers the most due to its mechanical wear and overheating of its components, due to the high temperatures it must withstand.
That error code indicates a failure of the yellow laser scanner. Unplug and leave for a few minutes, also make sure you are plugged directly into the wall and not into a surge protector.
Look inside the fuser opening to make sure there is no debris or jammed paper. Remove any debris or jammed paper, if found. Hold the handles on each side of the fuser and reinstall it in the printer.
Streaking, smudging, black lines, and double images are all symptoms of a bad fuser. When you notice these printing defects and experience problems, such as paper jams or wrinkles, this is a good sign to replace the fuser kit.
The fuser unit must be replaced every 100,000 pages, usually along with the transfer belt and feed rollers as part of a maintenance kit. The error code 010-351 indicates that the fuser has reached 75,000 pages and as a result has 25% life or less remaining.
The 50.1 fuser error message refers to a low temperature reading on your fuser. If you see the error message “50.1 Fuser Error” on your HP Color LaserJet 2820 or 2840 series printer, you probably need to replace the fuser. Fusers are a consumable part and are sold as part of a maintenance kit.
The P4014 series use a thin fuser sleeve as a medium to heat the paper. Error 50.8 suggests one end of the fuser is not heating up which may be damage to the sleeve or heavy media.
The Fuser is the piece that fixes the toner on the paper. This, like any other consumable part, wears out with the regular use of prints, since it is one of the components that suffers the most due to its mechanical wear and overheating of its components, due to the high temperatures it must withstand.
Streaking, smudging, black lines, and double images are all symptoms of a bad fuser. When you notice these printing defects and experience problems, such as paper jams or wrinkles, this is a good sign to replace the fuser kit.
Your printer monitors the life of your fuser. When the fuser reaches the end of its life, the printer displays 80 Fuser Exhausted. This message indicates it is time for you to replace the fuser. For best print quality, make sure you replace the fuser when the printer displays 80 Fuser Life Warning.
Streaking, smudging, black lines, and double images are all symptoms of a bad fuser. When you notice these printing defects and experience problems, such as paper jams or wrinkles, this is a good sign to replace the fuser kit.
Your printer monitors the life of your fuser. When the fuser reaches the end of its life, the printer displays 80 Fuser Exhausted. This message indicates it is time for you to replace the fuser. For best print quality, make sure you replace the fuser when the printer displays 80 Fuser Life Warning.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP LaserJet 1200 Early Feeding Causes Paper Jam
ANSWER : Seriously, dmzcompute, you are awesome! And this is just what the internet does so well: a specific fix for an esoteric problem, thus keeping a 15 year old machine alive another day. Thank you!

Read Full Q/A … :

HP LaserJet 1200

HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr

Read Full Q/A … :

HP LaserJet 1200

HP 4250 13.06.00 Fuser output paper stop !
ANSWER : pick up solenoid

Read Full Q/A … :

HP LaserJet 1200

HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply

Read Full Q/A … :

HP LaserJet 1200

HP DeskJet 510 – problem
ANSWER : Recently started to look for a trusted and high-quality work with a broker for binary options, but the search was not a very successful, and my friend who is already a few years makes this kind of activity offered me options brokers review – site who himself uses optionsbrokersreview.com

Read Full Q/A … :

HP LaserJet 1200

HP PSC 2410 clicking noise problem
ANSWER : I have the same issue… I’ve tried everything above… I don’t believe it’s dust as this happens on and off occasionally… I think I may need to make a youtube video of me “fixing” this printer! I’m really frustrated with this thing!! If it doesn’t work soon, I’m gonna by the solution in the form of a hammer!

Read Full Q/A … :

HP LaserJet 1200

Paper Feed Problem on HP R80
ANSWER : In the last examination it is our origination of death which chooses our responses to all the inquiries life puts to us. The most pleasant spot to be is in somebody’s idea; the most secure spot to be is in somebody’s petitions.

Read Full Q/A … :

HP LaserJet 1200

HP LaserJet 1160 pick-up problem
ANSWER : Take the black rubber roller out. Clean it and turn it 90-180 degrees so there is fresh rubber in the “corner”.

Read Full Q/A … :

HP LaserJet 1200