HP DeskJet 1220C

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary. Then reload the paper. If thick media does not feed, make sure you are loading it straight into the product, not at an angle. If paper jams when you print on both sides of the paper, try loading fewer sheets.
If the paper guides are too tight, the paper might be held in the tray and not allowed to feed into the product. Try the print job again.
Dust, paper fiber, and other debris might accumulate on the pick rollers and cause paper feed issues. To help prevent paper feed issues, clean the rollers inside the printer and in the duplexer (if equipped).
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
The Load Tray 1, Tray 1 Missing, or Insert Tray 1 error messages indicate that the printer has failed to detect the tray. The Tray Low or Tray Empty errors indicate that one or more of the tray sources are empty or low. These error messages also show which tray is missing, low, or empty.
The most common cause of this issue is paper misalignment. Make sure you properly insert the papers in the tray and avoid overfilling the tray. If this doesn`t solve the problem, check the troubleshooting section of the printer`s user manual.
This is often caused by the fact the pick-up roller is worn out. The layer of rubber around this plastic part overtime gets too smooth, preventing paper from feeding properly into the printer. This fix is not really hard, will take no more than half an hour and costs around 10,- (Euro or Dollar).

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

HP DeskJet 1220C

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :

HP DeskJet 1220C

Error Message "Paper out" when paper loaded
ANSWER : Check your paper tray settings as printer may be looking for paper from the manual feed tray on top of printer.

Read Full Q/A … :

HP DeskJet 1220C

Multiple paper feed
ANSWER : Most likely the pickup roller solenoid is sticking. The way it works is the solenoid energizes, pulling down a metal plate that releases the pickup roller. There is some foam on the base to quiet the clicking sound. The foam deteriorates and the plate sticks to the gooey residue. This allows the pickup roller to continue to turn instead of stopping after one revolution when the plate springs back up. That results in multiple paper being fed. Solution is to find the solenoid, which is at the end of the pickup roller shaft. Remove the sticky foam and preferably replace it with some thin sticky backed felt. You can find it at a hardware store as it is used on the bottom of chair legs.

Read Full Q/A … :

HP DeskJet 1220C

Keep getting a paper jam message. There is no jam.
ANSWER : You can quit wondering. Parts are unavailable. I’ve seen posts where people have 3D printed the parts or machined them out of metal.

Read Full Q/A … :

HP DeskJet 1220C

Paper Feed Problem on HP R80
ANSWER : In the last examination it is our origination of death which chooses our responses to all the inquiries life puts to us. The most pleasant spot to be is in somebody’s idea; the most secure spot to be is in somebody’s petitions.

Read Full Q/A … :

HP DeskJet 1220C

Error message to load paper and push OK, but not out of paper
ANSWER : I assist the binary options for a long time, and only half this past year I decided to alter the strategy for a better, she called for help Bing and he gave me this web site http://bestoptionstrategies.net .Now I focus on the suitable technique for themselves, and things gone up. I think everybody else faced with this particular problem. I believe my estimation will soon be helpful to you.

Read Full Q/A … :

HP DeskJet 1220C

Printer stops pulling paper from tray 2 after a few sheets
ANSWER : Sticking pickup roller solenoid. Pretty easy fix. You need to remove the right side covers. The back one just slides off, but the top holds the front one. I usually just take the 2 right side screws off and gently lift the top enough to pop off the side panel. Open the metal door on the formatter assy. Then release the tab in the middle. There’s also a tab at the front of the panel. When putting it back on, make sure you engage the rocker switch and the metal rod before pushing it into place. When you get it open, you’ll see the solenoid at the bottom front. There’s 1 screw holding it in place. Remove it and take the top plate and spring off. Be careful not to lose the spring. Then scrape off the gooey crap on top and clean off the plate as well. I put a piece of thin sticky backed felt in place of the remnants of the disintegrating sponge that HP uses. You can find it at the hardware store used for the bottom of chair legs.

Read Full Q/A … :

HP DeskJet 1220C