HP Color LaserJet 4500

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

The HP LaserJet Fuser helps make sure your HP toner is applied to your paper evenly and with vivid color and detail on every page without putting a major dent in your budget. It lets you print up to 150,000 pages of dynamic quality before you need to replace it.
Set the output bin cover aside. While grasping onto both sides of the fuser, push the blue levers upward and pull the fuser straight out. Once you have correct fuser matched up with your model, install the replacement fuser by inserting it and aligning the left side first.
The fuser unit or fuser is a critical part of any laser printer. Using pressure and heat, it fuses the toner powder onto the page to create a print, and without it, the printer cannot operate. Fuser units eventually need to be replaced after frequent use.
Konica Minolta bizhub C224 Fuser Unit – 110 / 120 Volt (Genuine) Specifications and Details: Original Mfr/Compatible : Genuine.
The fuser unit or fuser assembly, is a critical component of your laser printer. Using pressure and heat, it fuses the toner powder onto the page to create a print, and without out it, your printer cannot operate.
A component found in electrostatic printers, laser printers, and xerographic printers and photocopiers. The fuser unit is used to permanently bond toner to a substrate by applying heat and pressure. A fuser unit is made up of two rollers; one to apply heat and one to apply pressure.
50.2 error indicates that the printer is not heating up fast enough. This can be caused by a bad heating element in the fuser but can also be caused when the printer does not have adequate power due to overloaded circuits or being plugged into a power strip or surge bar that limits current flow.
If you have NOT recently replaced the fuser or heavily jostled the printer around, then the 50.7 Fuser error indicates you have an actual fuser failure (the gearing pressure is not releasing) and the fuser needs replacing.
Look inside the fuser opening to make sure there is no debris or jammed paper. Remove any debris or jammed paper, if found. Hold the handles on each side of the fuser and reinstall it in the printer.
The Fuser operates in the temperature range of 175 – 215o C (347-419o F).
Fuser part of printer and HSN Code 84439940 Imports in World – Import data with price, buyer, supplier, HSN code.
Import Data and Price of fuser roller under HS Code 84439959 | Zauba.
A fuser unit is a pair of heated rollers within the printer that fuses the toner onto the paper being printed on. Toner particles are pulled to the paper to create the desired text and images as the paper passes the imaging drum.
The message `Fuser Error` or `Self-Diagnostic` means either the fuser has reached the maximum temperature allowed or there has been an error in detection of the correct temperature during specific times of the printing process.
There are replacement rollers and sleeves on the market that you can replace and turn a non-functional fuser into a good working one. Rebuilding fuser assemblies is not a new thing. Copier technicians have been doing it for years since the first office copier was created.
The message “Replace Fuser” will appear on the display when the machine has printed approximately 100,000 pages (at 5% coverage on letter/A4 paper). The fuser unit is a periodic maintenance part and should be replaced to maintain optimum print quality and reliability and to prevent paper jams.
A high fuser temperature error has occurred. Note: A fuser error might occur because of inadequate power supply, inadequate line voltage, or a fuser problem.
The flag located right of the pick-up roller has a fixed position. If the flag becomes stuck or broken, it will produce a 60.02 tray lift error or a “LOAD PAPER” message. If this flag is broken or if the sensor has failed, the RM2-6368 paper feed guide will need to be replaced.
When a 50.4F. 00 error is displayed on the control panel, it indicates that there is an issue with the fuser or the power outlet where the printer is connected. Turn the printer off, and then back on to clear the error. Ensure that the power outlet, to which the printer is connected, is in good working condition.
If you are seeing the message 50.9 Fuser Error on your HP LaserJet P4014, P4015, P4015 series printer, you have either a failing fuser or the wrong model fuser installed in your printer. (The fuser is the consumable part in your printer which heats up and bonds toner to the paper.
That error code indicates a failure of the yellow laser scanner. Unplug and leave for a few minutes, also make sure you are plugged directly into the wall and not into a surge protector.
xx service fuser error. The printer is displaying a 922 type Service Fuser error (for example, 922.01, 922.54, 922.99, etc.). This type of error message indicates that the fuser unit inside the printer is operating below the proper temperature.
This error is primarily caused by one of the following conditions: A transfer alienation failure in which the ITB is stuck and unable to properly engage the internal transfer rollers. The SR9 sensor (the primary transfer roller disengagement sensor) has gone bad. The fuser drive assembly has failed.
That error is an ETB Motor startup problem. The ETB Motor is part of the ETB assembly, which is the thing you reseated. So it is possible that replacing the ETB will resolve the issue. If my answer solves your problem please mark it as a solution by clicking the button under the post.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP Color Laserjet 3800 problem when printing color
ANSWER : Do a cold reset

Read Full Q/A … :

HP Color LaserJet 4500

HP Color Laserjet 2840 spitting out blanks
ANSWER : Moe- You are the man!

Read Full Q/A … :

HP Color LaserJet 4500

HP Color Laserjet blank pages – only jetdirect page
ANSWER : What about the engine test? To do that, drop down the front tray. Feel around on the left side at the top and you’ll feel a little plastic dongle. If you lift up on that it will initiate an engine test page. That will be a page containing lines of each color.

Read Full Q/A … :

HP Color LaserJet 4500

HELP! HP Color Laserjet 5500dn (formatter prob??)
ANSWER : Italiano:

Read Full Q/A … :

HP Color LaserJet 4500

HP Color LaserJet 4700
ANSWER : Saludos Amigo le Que le Pasa a tu Impresora Es Que Tienes rota El Sistema de sierre de la puerta con el Cierre de los tóner es Por Esa Razon Que No Cierra los tóner Si Quieres repararla Ponte en Contacto Madrid Seis Cinco Cinco Tres Cuarenta dos cuarenta y uno Reparación en el Momento saludos

Read Full Q/A … :

HP Color LaserJet 4500

Reset HP Color Laserjet 4700 transfer kit
ANSWER : How about the situation when resistor does not reset the transfer belt count and even new transfer belt out of the box is not doing it. Do you have any idea how to solve this problem? I did reset transfer belts and fusing units on several HL 4700 printers with no problem but also I came across few which were not possible to reset even with oryginal parts.

Read Full Q/A … :

HP Color LaserJet 4500

My 2550n Color LaserJet does not want to print in color
ANSWER : That model had issues with the carousel solenoid sticking. That might explain why it works after you let it sit for 10 minutes. The solenoid gets hotter with use which causes the deteriorated foam on it to become sticky and hold down the release plate instead of letting it go. This allows the carousel to spin when it is supposed to stop for each color. The solenoid is located on the right side of the printer. If you open the lid, it is just behind the opening at the top right. You need to remove the top of the printer and scrape off the goo on top of the solenoid body. I put a piece of thin sticky backed felt to replace it. Other people use electrical tape.

Read Full Q/A … :

HP Color LaserJet 4500

HP Color LaserJet 4550 Streaking
ANSWER : hello,

Read Full Q/A … :

HP Color LaserJet 4500