Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

The message `Fuser Error` or `Self-Diagnostic` means either the fuser has reached the maximum temperature allowed or there has been an error in detection of the correct temperature during specific times of the printing process.
The fuser unit is a heated roller that melts the toner particles onto the page as it passes through. This seals the toner to the page so it`s no longer in powder form and makes sure that the toner doesn`t smudge of fall off the paper when it comes out of the printer.
The fuser unit or fuser is a critical part of any laser printer. Using pressure and heat, it fuses the toner powder onto the page to create a print, and without it, the printer cannot operate.
This error might display if the fuser temperature becomes too hot. Follow these steps to turn off the printer and allow the fuser to cool before printing again. Press the Power button to turn off the printer. Disconnect the power cord from the rear of the printer.
The message “Fuser Kit Low” or “Fuser Kit Very Low” on your HP Color LaserJet M553 series printer is a warning that you have reached the recommended number of prints for your fuser assembly. (The fuser assembly is the consumable part in your printer which heats up and bonds toner to the paper.
A fuser unit is a pair of heated rollers within the printer that fuses the toner onto the paper being printed on. Toner particles are pulled to the paper to create the desired text and images as the paper passes the imaging drum.
The fuser unit or fuser assembly, is a critical component of your laser printer. Using pressure and heat, it fuses the toner powder onto the page to create a print, and without out it, your printer cannot operate.
Streaking, smudging, black lines, and double images are all symptoms of a bad fuser. When you notice these printing defects and experience problems, such as paper jams or wrinkles, this is a good sign to replace the fuser kit.
The message “Replace Fuser” will appear on the display when the machine has printed approximately 100,000 pages (at 5% coverage on letter/A4 paper). The fuser unit is a periodic maintenance part and should be replaced to maintain optimum print quality and reliability and to prevent paper jams.
Your printer monitors the life of your fuser. When the fuser reaches the end of its life, the printer displays 80 Fuser Exhausted. This message indicates it is time for you to replace the fuser. For best print quality, make sure you replace the fuser when the printer displays 80 Fuser Life Warning.
Turn off your printer and unplug it, wait 30 seconds, plug your printer back in, and then turn the printer back on.
This error might display if the fuser temperature becomes too hot. Follow these steps to turn off the printer and allow the fuser to cool before printing again. Press the Power button to turn off the printer. Disconnect the power cord from the rear of the printer.
Your printer monitors the life of your fuser. When the fuser reaches the end of its life, the printer displays 80 Fuser Exhausted. This message indicates it is time for you to replace the fuser. For best print quality, make sure you replace the fuser when the printer displays 80 Fuser Life Warning.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

HP 4250 13.06.00 Fuser output paper stop !
ANSWER : pick up solenoid

Read Full Q/A … :
Unknown Printer

HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply

Read Full Q/A … :
Unknown Printer

REMOVE FUSER UNIT
ANSWER : It looks real easy. https://www.youtube.com/watch?v=fbilywC620A

Read Full Q/A … :
Unknown Printer

fuser bushings
ANSWER : Kind of vague. Are you asking how to install fuser bushings?

Read Full Q/A … :
Unknown Printer

FUSER JAM
ANSWER : I have the same problem. please help

Read Full Q/A … :
Unknown Printer

fuser
ANSWER : You can buy just the upper fuser roller that is the cause of your problem. The real problem is that there are no instructions for rebuilding the fuser. The Brother fusers are a bit difficult to take apart.

Read Full Q/A … :
Unknown Printer

Fuser Flag Sensor Spring has fallen out
ANSWER : Should be in the service manual. http://www.manualslib.com/products/Brother-Dcp-9020cdw-3385466.html

Read Full Q/A … :
Unknown Printer

Fuser burning labels
ANSWER : Make sure the labels are rated for a laser printer as the ones for inkjet printers cannot tolerate the heat produced by a laser printer and will tend to scorch. If the labels aren’t rated for a laser printer then there may be nothing wrong with printer.

Read Full Q/A … :
Unknown Printer