Epson Stylus Photo R200
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
When the red H ink light flashes, one or more ink cartridges are low on ink. When the red H ink light stays on, you need to replace the cartridge(s). When you print, you`ll also see a message on your screen telling you which cartridge is low or empty.
Ink in a cartridge is low. You can continue printing, or check which cartridge is low and replace it. An ink cartridge is expended or not installed correctly. Replace or reinstall the cartridge.
if you have all lights flashing and your inkjet Epson printer reporting a possible paper jam or fatal error but there is no paper jammed in the printer maybe the problem is the light sensor first of all look at the waste ink pad counter to make sure the problem isn`t the waste ink pad try to change all ink cartridges …
A `Paper has Jammed` message and light blinks
Remove any ejected paper from the front or back of the printer. Open the paper tray cover. Remove any loose photo paper from the paper tray, and then check for and remove any bent, wrinkled, or torn paper.
Check to see if the lamp is burned out, broken, or installed incorrectly. Reseat or replace the lamp as necessary. Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects.
Projector Lamp is Burnt Out
If the light is flashing red or orange, you need to replace the lamp. If the projector turns on, but the image doesn`t appear, your lamp may be burnt out. If the image being projected is discolored or dim, the lamp may burn out soon.
Red ink light flashes One of the cartridges is low on ink. Check the message that appears on your screen to determine which cartridge is low. Make sure you have a replacement cartridge. Red ink light is on One of the cartridges is out of ink or not installed.
Yes, you can reset the print settings to their original, default values. Press and hold down the Cancel button for 3 seconds. When the message to reset the printer to default settings appears, press OK to reset the print settings.
It is usually on the top right-hand side of your printer, near any digital display screen that the printer may have, and where the button used to turn the computer on and off is also located. Find the button marked Pause/Reset on the row of buttons on the control panel.
If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.
Print blemishes after inserting a new cartridge. Slow print times. Abnormal noises. Paper jams and ripped paper.
When your projector/TV is flickering, or displaying a green/pink tint, this usually means there is an issue with an HDMI connection. Find your switcher, unplug all of the cables, then plug them back in where they were. If this doesn`t fix it, unplug and replug the HDMI from the source device (Apple TV, Computer, etc.).
It is time to replace the lamp when: The projected image gets darker or starts to deteriorate. The message LAMP REPLACE appears on the screen when the lamp comes on and the lamp warning light is flashing orange. To maintain projector brightness and image quality, replace the lamp as soon as possible.
Press the FREEZE button on the remote control. The “FREEZE” indication will appear on the screen , and the projector will go into the FREEZE mode, which the picture is frozen. To exit the FREEZE mode and restore the screen to normal, press the FREEZE button again.
Red ink light flashes One of the cartridges is low on ink. Check the message that appears on your screen to determine which cartridge is low. Make sure you have a replacement cartridge. Red ink light is on One of the cartridges is out of ink or not installed.
Turn off the printer. Wait at least 5 seconds, then turn it back on. If the error message still appears, write down the error number listed in the LCD panel (Cffff/Eggg), turn off the product, unplug the power cord, then contact a qualified service representative.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Epson Stylus Photo R230 – flashing red lights fix
ANSWER : REDLIGHT
Read Full Q/A … :
Epson Stylus Photo R200
All lights flashing on turn on
ANSWER : If it is new, return it and get a replacement.
Read Full Q/A … :
Epson Stylus Photo R200
Epson Stylus Photo R200 – flashing red lights
ANSWER : The R800 will flash the ink and paper lights alternately when the ink pads are assumed to be full from extensive head cleaning. Sometimes, if not always, the head will lock into place on the right side above the ink head cleaning sponges that release ink to the lower ink pads.To correct the problem you need to clean the sponge area, I use cotton swabs. If the head is locked to need to release the carriage lock with a screwdriver. This will require removing the cover, but not necessarily the bottom of the unit.There is a 179 page service manual available for download for $16.50. There are free downloads of this manual, but usually are missing the 100 pages.You can remove the cover by:1. Remove the three screws on the rear housing (One to the left of the power plug, one on the opposite side and one in the lower middle bottom.2. Remove the three screws inside the upper housing (Just under the lid where the hinge is).3. Remove the screw under the left and right side in back below the vents.4. In the back pull the white ribbon closest to you out of the block, do not try to remove the block itself.5. Place a screwdriver into the slot both on the right and lift of the bottom corners on the back to release the hooks that hold the upper unit.6. Lastly, put a screwdriver into the notches on the bottom of the printer located in the front right and left, they are spring loaded.7. Remove cover.8. The head lock release screw is in the right side of the printer and is partially covered by the lower housing. I drilled a half inch hole into the side as to be able to insert a screwdriver. Turn the screw to the left and the head will rise out of the locked position. You only need to turn enough to release the head.9. Clean the sponges and any areas you see with excess ink.10. Place the cover on the unit enough to plug the white ribbon back in and turn the unit on.If the printer lights stop flashing then you are all set.
Read Full Q/A … :
Epson Stylus Photo R200
error 59.99 turn off then turn on
ANSWER : Read this forum thread http://www.fixyourownprinter.com/posts/51164
Read Full Q/A … :
Epson Stylus Photo R200
Red Light – Please help!
ANSWER : Here is the vid:
Read Full Q/A … :
Epson Stylus Photo R200
the indicator lamp below the ink indicator sign bottom is lighting red in colour rapidly.
ANSWER : We have free Trial Reset Key.
Read Full Q/A … :
Epson Stylus Photo R200
Epson Stylus C90 (Red Light Continuously Blinks)
ANSWER : It looks like General Error occurs. Check for foreign objects inside the printer which may block the movement of printhead carriage, paper feed, etc.
Read Full Q/A … :
Epson Stylus Photo R200
Flashing Amber light
ANSWER : Make 1) check that the back of tray that is adjustable is against the paper and 2) the paper sensor for the tray moves freely – if it gets stuck it will cause that error.
Read Full Q/A … :
Epson Stylus Photo R200