Brother MFC J410W
Hi,
Experienced technical support provide their insights in answering this question :
Access the internal maintenance mode by pressing the Menu/Set button, then press * 2 8 6 4 within 2 seconds. This should put you in the maintenance mode menu. Enter 80, and then scroll down with the arrow down (round) key. You will find an entry listed as purge count. If number is over 6000, enter 2 7 8 3.
How to Identify and Fix Common printer Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Remove all ink cartridges from the printer and gently clean the contacts on the printer and cartridges. Unplug your printer and leave for 10 – 20 minutes. Plug the printer back in and wait for the message to insert new cartridges. Replacing any that are almost empty, install all inks back in the printer.
It means that your device is not able to work up to its maximum potential. It is a common message that indicates that the print head of the Brother Printer is encountered with the temperature error or might have an internal electric issue.
During a print job, the printer stops feeding pages, an E4 error displays and the Resume light blinks. This indicates that paper might be jammed inside the printer. Note: Paper jams can be real or false.
According to the manual 4F means “DXE IPL is started“, but nothing else or more info to develop. Also the only beep codes the manual refers are an infinite loop of Long + a number of short beeps, not a single instance of 2 rounds of three long beeps.
1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.
Causes of Motherboard Failure:
Electric and voltage fluctuations. Dust particles, smoke, debris, etc. Liquid damage. Overheating caused my fan failure.
Common symptoms of motherboard issues are similar to CPU problems: The system does not display anything; an error code appears; one or more beeps occur; the system locks; the system reboots; a Windows BSOD (blue screen of death) appears; or one or more of the ports, expansion slots, or memory modules fails.
[Settings]>[All Settings]>[Initial Setup]>[Reset]. to display the type of reset functions, and then press the reset function you want to use. The LCD displays [Machine will reboot after resetting. Press [OK] for 2 seconds to confirm.].
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Error Message – Unable to Init. 4F
ANSWER : Access the internal maintenance mode by pressing the Menu/Set button, then press * 2 8 6 4 within 2 seconds. This should put you in the maintenance mode menu. Enter 80, and then scroll down with the arrow down (round) key. You will find an entry listed as purge count. If number is over 6000, enter 2 7 8 3.
Read Full Q/A … :
Brother MFC J410W
Brother MFC-9125CN error message is: Print Unable 28
ANSWER : Print Unable 28
Read Full Q/A … :
Brother MFC J410W
printer error code unable to print 4f
ANSWER : Follow these instructions:
Read Full Q/A … :
Brother MFC J410W
Message is unable to change 4f
ANSWER : You can try this free reset procedure. If that fails, you need to replace the printhead. They cost about $80.
Read Full Q/A … :
Brother MFC J410W
Screen Error message – unable to do anything..
ANSWER : I have the same message and I can’t found any solutions can you help ?
Read Full Q/A … :
Brother MFC J410W
Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.
Read Full Q/A … :
Brother MFC J410W
Error message reads remove and check right cartridge
ANSWER : You can try cleaning the contacts on the back of the cartridge and the ones that they contact in the printer. Other than that, you have to replace the cartridge. I once had one that did the same thing. I swapped the cartridge with another printer of the same model and both printers worked fine. I swapped them back and the original printer got the same error. The other printer had no problem with either cartridge. I swapped them back and left them that way.
Read Full Q/A … :
Brother MFC J410W
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Read Full Q/A … :
Brother MFC J410W