HP Photosmart C7250
I am getting the message that I can print because of an error in the printing system.
Experienced technical support provide their insights in answering this question :
What is the exact message you are getting?
How to Identify and Fix Common printer Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.
If your printer is turned on, disconnect the power cord from the printer. Keep the power plug unplugged for 60 seconds, reconnect the power cord to the wall, and turn on the printer. If the error persists, remove the cartridge from the printer, clean the cartridge contacts with a cloth, and reinstall the cartridges.
Solution one: Remove the ink cartridges and the printhead, restart the printer, and then reinstall the printhead and the ink cartridges. Removing and reinstalling the ink cartridges and the printhead can clear the error displayed on the front panel.
For the HP 932-933 ink-series printer error message “Ink System Failure” or “Printhead Failure” typically one of the ink cartridges could be low (or empty) on ink. It also possible that a poor seal is present between the cartridge and the internal printhead and the cartridge may need to be replaced with a new one.
Just above the circuit board on most printer cartridges, you`ll find a small button. You`ve seen these tiny buttons before on cell phones, phone chargers, etc. This is your reset button, and the only way to get in there is either with a paper clip or the tip of a pen (which will leave a tiny ink smudge on the button).
If your printer is turned on, disconnect the power cord from the printer. Keep the power plug unplugged for 60 seconds, reconnect the power cord to the wall, and turn on the printer. If the error persists, remove the cartridge from the printer, clean the cartridge contacts with a cloth, and reinstall the cartridges.
Check for obstructions in the carriage path Open the cartridge access door to get to the carriage inside the printer. Make sure the carriage is not obstructed by gently sliding the carriage side to side. Look for and remove any obstructions in the carriage path, such as crumpled paper or dislodged labels.
Check for obstructions in the carriage path Open the cartridge access door to get to the carriage inside the printer. Make sure the carriage is not obstructed by gently sliding the carriage side to side. Look for and remove any obstructions in the carriage path, such as crumpled paper or dislodged labels.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Error in printing system
ANSWER : What is the exact message you are getting?
Xerox 7760 Wrong paper size error when trying to print to A4
ANSWER : At first you could try to print using the Multifunction/Bypass Tray on the left side of your printer.
printer error code unable to print 4f
ANSWER : Follow these instructions:
when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?
Error A2 unable print
ANSWER : http://fixyourownprinter.com/posts/75749
hp deskjet 3420- system error
ANSWER : Hi I am having problem in printing from java file , I followed all your steps but C:\\WINDOWS\\system32\\spool\\drivers\\w32x86\\3 after this I am getting no files in this folder ,please help me as I am struggling to get print from java since a week
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Print file sent but no printing occurs
ANSWER : Been working on these since they first were released. Never seen a problem like yours. If it happens again, try doing an engine test, as it bypasses the formatter board. The engine test is located at the right side of the manual tray opening. Look for a hole in the side wall. Stick something like a paper clip into it to actuate the test button. It will then print a lined test page. If it does that, then it points to the formatter board as the cause of your problem.