Ricoh Aficio MP C4000
everytime you turn it on error and a message to call service SC582

How to Identify and Fix Common printer Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

The Ricoh error code 142 / SC142 is a white level (glass) adjustment problem during auto gain control. Some of the causes of this error include: Dirty exposure glass or optics section. SBU board is no good.
The Ricoh copier error code 101 / SC101 is an exposure lamp error or the SBU board is defective. It can also mean the standard white level on the glass was not detected properly. Check for a dirty scanner mirror or that the scanner mirror is out of position.
The Ricoh copier error code 440 / SC440 is a main motor lock error code. To reset this error try the code: “Clear Mode”+107+”Clear/Stop” hold for 5s. Turn ON and OFF the Main Switch.
If the “ERR (993) Power Off On / Call Service if error reoccurs” message appears, there might be condensation inside the printer. You can dry the printer`s interior by performing the de-condensation procedure.
SMTP Error 451 : The action has been aborted by the ISP`s server.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
This section takes the error code 391 (indicating that the paper is jammed in Tray 1) for example. For the error code 392, 393 or 394, remove the jammed paper by following the same procedure. If paper jams occur frequently, clean the paper feed roller.
Error message 988 or 990 is a clogging warning. In order to assist you, we need you to provide us with pictures of the following items to [email protected].
The Ricoh copier error code 285 / SC285 is a line position error code problem. If this is happening: The MUSIC error occurs 4 times since the last time the main power was turned ON.
Thermistor is bent or gone bad. You may need to replace it. Or, the thermistor position is incorrect.
Malfunction due to Exit junction gate overload; the sensor shielding plate is deformed, damaged or not attached properly.
As the error message hints, the error 740 printer is often related to the network administrator privileges. In addition, a temporary glitch, outdated or corrupt printer drivers, and improper printer settings can trigger the 740 error as well.
The Ricoh copier error code 670 / SC670 is an engine startup problem. To reset this error try the code: “Clear Mode”+107+”Clear/Stop” hold for 5s. Turn ON and OFF the Main Switch.
Verify that You Have Loaded Paper into the Printer

So, have a check if Ricoh/Brother/Canon/HP printer in error state happens. Just turn off the device, load paper, and wait a few minutes. Then, check if the error is removed.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Scanner error keeps coming up
ANSWER : I am having the same problem with my Epson Workforce 645

Read Full Q/A … :

Ricoh Aficio MP C4000

My encolder has come off and i Cant get the screws to come out to open up
ANSWER : torx driver for an hp if thats what you have

Read Full Q/A … :

Ricoh Aficio MP C4000

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :

Ricoh Aficio MP C4000

Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.

Read Full Q/A … :

Ricoh Aficio MP C4000

HP CLJ CP 5225 ERROR 55.0601
ANSWER : my printer cp5225 is giving me error code 55.0601 message which i can’t fix please help

Read Full Q/A … :

Ricoh Aficio MP C4000

Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.

Read Full Q/A … :

Ricoh Aficio MP C4000

My printing come out blurred
ANSWER : doris…There are usually 2 reasons for blurry output on this printer. First, make sure that the alignment is correct. You can get to it from the maintenance tab on the software that came with the printer. The other common cause of blurring is debris under the printhead. Hope this helps.

Read Full Q/A … :

Ricoh Aficio MP C4000

HP 9040 MFP Error code
ANSWER : bonsoir

Read Full Q/A … :

Ricoh Aficio MP C4000