Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

The fan on the left side of the printer is not working right. Remove the top cover and the left side cover and see if the fan is turning and if not if just gummed up over the years remove the fan and clean it up to get it spinning again. If that does not work, then the fan will need to be replaced.
This is a rotational error on a fan. This fan is the located on the left hand side (when you are facing the front) and is the one located closer to the back.
50.2 error indicates that the printer is not heating up fast enough. This can be caused by a bad heating element in the fuser but can also be caused when the printer does not have adequate power due to overloaded circuits or being plugged into a power strip or surge bar that limits current flow.
Most generate an error code if a fan stops running (or even slows down). In a small printer with only one fan, this is a simple “57 SERVICE” error. In a larger printer with multiple fans, decimals (57.1, 57.2, etc.) are used to identify which fan has failed.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
It means that tray 2 and its lift motor are not working. Do you hear thumping or banging sounds? This is also common for a 60.2 error.
This error is primarily caused by a transfer alienation failure in which the ITB is stuck and unable to rotate, the SR9 sensor (the primary transfer roller disengagement sensor) has gone bad or the fuser drive assembly has failed.
The 59.40 is a “fuser rotational error“. Meaning the fuser was unable to rotate causing this error.
57 is a fan error, check are the fans are rotating, and make sure the printer power is plugged directly into the wall socket. 57 is a fan error, check are the fans are rotating, and make sure the printer power is plugged directly into the wall socket.
A product error has occurred where a memory tag CPU error was detected, or there is a problem with the air sensor or power supply. 58.04 = check low-voltage power supply (ECU) Make sure the line voltage and current source meet the electrical specifications for the product. To resolve problems with the power supply: 1.
The laser/scanner assembly needs to be replaced as one of the motors has gone bad inside the assembly.
A product error has occurred where a memory tag CPU error was detected, or there is a problem with the air sensor or power supply. 58.04 = check low-voltage power supply (ECU) Make sure the line voltage and current source meet the electrical specifications for the product. To resolve problems with the power supply: 1.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :
Unknown Printer

newly installed printer…can scan but cant be set as a default printer???
ANSWER : ITS AN EPSON L210…

Read Full Q/A … :
Unknown Printer

Difference Between Laser Printer and InkJet Printer
ANSWER : Laser uses toner which is a powder that gets melted onto the page. Inkjet uses ink that gets squirted onto the page.

Read Full Q/A … :
Unknown Printer

Printer error Oxc18a0201
ANSWER : Have no idea what model you have, but try this forum post or search through the site using your model and error.

Read Full Q/A … :
Unknown Printer

canon printer error
ANSWER : Here are the procedure to fix Canon smartbase MP730 printer error ##334

Read Full Q/A … :
Unknown Printer

PRINTER MX 320 CANON ALL IN ONE PRINTER
ANSWER : Probably a worn feed roller. You can try cleaning it with a damp rag as it might just be covered with paper dust.

Read Full Q/A … :
Unknown Printer

printer error fix
ANSWER : Epson 2540

Read Full Q/A … :
Unknown Printer

Canon i255 printer head error
ANSWER : Sometimes the print head issues are brought on not by a flawed print head but rather by a “gunky” stopping station. The stopping station is the spot where the print head “rests” when it is not printing. Generally it’s on the right half of the printer (taking a gander at the printer from the front). The stopping station has elastic seals that should encompass the print head when it’s stopped.

Read Full Q/A … :
Unknown Printer