Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

55 error codes are NVRAM issues and rarely caused by the cartridge. Bad power is a common cause. Make sure the printer is plugged directly into the wall outlet and not into a surge protector, multi outlet strip or UPS.
The 55.1 error relates to a memory error on the dc controller. Make sure the printer is plugged directly into the wall socket and not a surge protector. If the error is still there, then you need to contact hp customer care in your location to get warranty service since it would appear parts will need to be replaced.
It is a Firmware error meaning the firmware that was installed was corrupt in some way (write error or a faulty thumb drive). Turn off the printer and disconnect the cables and allow at least 15 minutes for the printer to fully discharge.
Event ID 55 is reported if the operating system detects the file system structure on the disk is corrupt and unusable. This is typically related to a failure condition with the disk subsystem and may stop the machine from functioning correctly.
The definition of this error means that the RAM is not installed. However, not every Q Code 55 error indicates a memory problem. In some cases, incompatibilities may also exist between the processor and the motherboard. In this type of problem, Q Code 55 errors may occur.
If one or more toner cartridges are installed incorrectly, this may result in a 54.2 carousel rotation error. This error is typically accompanied by a loud grinding noise. NOTE: The carousel is the rotating part under the top cover to which all four print cartridges attach.
Sometimes, simply restarting both your computer and printer can be the solution to the “printer in error state” issue. Power off your printer and computer completely, leaving them in this state for a few minutes, then turn them on again to see if the problem is gone.
The product has detected a failure to access the Line Sensor EEPROM. 1. Switch the power off from the back of the product and disconnect the power cord. Reconnect the power cord and power on the product.
that set of codes is pointing to a RAM issue ad 45 is a post Memory Initialization code and 55 is Memory Not installed.
A new page should print with a claim code. If the page does not print, see the email address on the printer display. The first part of the HP ePrint address preceding “@hpeprint.com” is the claim code. For example, if your HP ePrint email is “abc@hpeprint.com”, then “abc” is your claim code.
a misprint or misspelling in a text.
Event ID – 55

RESOLUTION: To resolve this issue, back up the volume that contains the corrupted file(s) and exclude the corrupted file(s) from the backup job. Reformat the volume, and then restore from the backup.

Error code 55, Over DC voltage in AC output Trouble shooting： Step 1. Disconnect the load, grid input and solar input. Just connect battery and turn on the inverter.
Code 55 is a memory error.
Re: GA-Z170X-Gaming 7 Error Code 55 Memory Initialization Error. The memory controller is in the CPU. So have you check the CPU socket to make sure you don`t have any bent pins. Because by what you saying it doesn`t matter if you have the memory in or none, you get the same code.
The toner cartridges that are placed incorrectly would display the error message along with the information regarding the wrong rotation of the carousel component. Discussed below are some points related with the symptoms and tips to fix the error: Symptoms. Remove and reinstall the cartridges.
00 or a 50.22. 11 error displays on the control panel, it indicates an issue with the fuser warming up. Step 1: Turn the printer off, and then on. Turn the printer off, and then on to clear the error.
If the error code 33.05 is displayed once inserting the eMMC and or replacing the Printer`s Formatter, an updated firmware must be performed. The printer may broad cast this error along with the “Security Alert” message.
This is a rotational error on a fan. This fan is the located on the left hand side (when you are facing the front) and is the one located closer to the back.
The 59. F0 has been a common error code on the HP CLJ M452 and M377 / M477 MFP models. The printers service manual references this error to a “drum motor assembly” but in most cases has been resolved by replacing the Transfer Belt assembly (RM2-6454).
Summary: Error Code 0x80070005 — also known as `Access Denied` error — is a type of Windows update error. It occurs when the system or user lacks the required files or permissions to change settings at the time of Windows update.
59. F0 Error is displayed when primarily caused by a transfer alienation failure in which the ITB is stuck and unable to rotate or because the SR9 sensor (the primary transfer-roller-disengagement sensor aka Sensor K) has gone bad.
If a print job of yours repeatedly causes this error, it may indicate a problem with the print job. Try breaking your document up smaller before printing it. I would recommend to run a firmware update on the printer.
25 years of experience. Hello the “Error 55” usually indicates a failed wheel speed sensor (or dirt or corrosion preventing one of them from reading correctly). This failure is probably what is turning on your ABS warning, and prevents cruise control from working (intentional). Check your wheel speed sensors.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :
Unknown Printer

Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.

Read Full Q/A … :
Unknown Printer

Scanner error keeps coming up
ANSWER : I am having the same problem with my Epson Workforce 645

Read Full Q/A … :
Unknown Printer

HP CLJ CP 5225 ERROR 55.0601
ANSWER : my printer cp5225 is giving me error code 55.0601 message which i can’t fix please help

Read Full Q/A … :
Unknown Printer

Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.

Read Full Q/A … :
Unknown Printer

HP 9040 MFP Error code
ANSWER : bonsoir

Read Full Q/A … :
Unknown Printer

Density Shutter Error
ANSWER : I’ve never worked on one of those printers, but I have never, ever seen 1 valid solution for printer repair on fixya.com I read the replies there when I need a good laugh. Makes me wonder what the “techs” on that forum actually do for a living. It certainly couldn’t be printer repair.

Read Full Q/A … :
Unknown Printer

52.0 SCANNER ERROR
ANSWER : Laser scanner assembly.

Read Full Q/A … :
Unknown Printer