Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

yz Fuser error To continue turn off then on is displayed on the control panel, it indicates that there is an issue with the fuser. The XX and YZ are two digit codes that provide information on the specific issue causing the error. Press the power button to turn the printer off, and then back on to clear the error.
00 Fuser error indicates you have an actual fuser failure and the fuser needs replacing. Fusers are a consumable part and they are the main component in a printer maintenance kit; it is expected over the life of the printer you will replace the maintenance kit several times.
A high fuser temperature error has occurred. Note: A fuser error might occur because of inadequate power supply, inadequate line voltage, or a fuser problem.
Look inside the fuser opening to make sure there is no debris or jammed paper. Remove any debris or jammed paper, if found. Hold the handles on each side of the fuser and reinstall it in the printer. Close the rear door or right door (depending on the printer model).
Error 50 is Invalid destination number.
Error code 50 indicates your Mac could not copy or move files from external storage devices. The whole process gets stuck with no visible progress.
50.2 error indicates that the printer is not heating up fast enough. This can be caused by a bad heating element in the fuser but can also be caused when the printer does not have adequate power due to overloaded circuits or being plugged into a power strip or surge bar that limits current flow.
50.AF is a low fuser temperature error and usually caused by a defective fuser. Resetting the printer is unlikely to resolve this error.
If you see this error code 50.5 on an HP LaserJet 4200, 4240, 4250, 4300, or 4350 series printer, the fuser installed in the printer is registering as an incorrect fuser for that model printer.
When a 50.22. 00 or a 50.22. 11 error displays on the control panel, it indicates an issue with the fuser warming up.
The 50.1 fuser error message refers to a low temperature reading on your fuser. If you see the error message “50.1 Fuser Error” on your HP Color LaserJet 2820 or 2840 series printer, you probably need to replace the fuser. Fusers are a consumable part and are sold as part of a maintenance kit.
This error indicates that there is an issue with the fuser.
Fix 1: Refresh DISM

When you see DISM error 50 on Windows 10, the first thing you can try is to refresh the DISM tool. It`s quite easy. Step 1: Press Win + R to invoke Run window. Input cmd in the box and press Shift + Ctrl + Enter to run Command Prompt as administrator.

Re: Sky Go app on iPad error 50-2 code

Are you at home and connected to your Wifi connection when this error appears, if so try disabling the Wifi on your device and then enable it again after a few minutes.

I found the following: Error 50 means that the heating of the fuser unit is no longer working. This is usually a burnt-out heating lamp,or a defective thermal fuse.
Error code 50 occurs if the system is unable to back up existing assets while installing.
I found the following: Error 50 means that the heating of the fuser unit is no longer working. This is usually a burnt-out heating lamp,or a defective thermal fuse.
Er/30 or Er/50 to Er/55 displays and the Attention light is on. The printer is in an error state. Reset the printer to resolve the issue. With the printer turned on, disconnect the power cord from the printer.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

What repair needs to be done for a "50 needs repair" message on an HP Laserjet IIIP?
ANSWER : I don’t know what you mean by good toner cartridges. They haven’t been built in about 10 years, so if they are new OEMs in the box, they are guaranteed to fail. The 50 error on that printer is mostly a burned out fuser lamp. This site was sold, so as you can see, there are no more kits available.

Read Full Q/A … :
Unknown Printer

HP LaserJet 49 Error Troubleshooting
ANSWER : One must give a chance to 25dollarsupport its a Fix $ price Computer Tech support company, which is the best option in present crowded market. Quite dependable and cost effective..

Read Full Q/A … :
Unknown Printer

HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply

Read Full Q/A … :
Unknown Printer

HP Laserjet 4250 – RFU LOAD ERROR
ANSWER : Italiano:

Read Full Q/A … :
Unknown Printer

evenly spaced horizontal lines on hp laserjet III printout
ANSWER : The lines would be a toner cartridge problem. Which paper tray? The MF tray or the optional paper cassette?

Read Full Q/A … :
Unknown Printer

HP Laserjet M3035xs error 13.17.00
ANSWER : If the misstep thinks of no interface join connected with the unit, pay for my research paper then most times the issue is the hard circle and it ought to be supplanted.

Read Full Q/A … :
Unknown Printer

HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr

Read Full Q/A … :
Unknown Printer

HP Laserjet 4100 Error (13.1)
ANSWER : I am pretty late to the party for this discussion but I am incredibly thankful to the person that posted this “fix” that I can barely imagine it. My 4100 had developed the dreaded paper jam described above and I had no idea what was causing it. I replaced a number of rollers only to have the same problem re-occur with no solution in sight.

Read Full Q/A … :
Unknown Printer