Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Damage or corruption of the printer drivers installed on the system can also cause “Printer not activated, error code 41. Users experiencing this issue need to completely remove the printer drivers installed on the system using the device manager and then reinstall the printer drivers.
The 41.2 error in the LaserJet 5Si, 8000, 8100 and 8150 is typically caused by high voltage arcing that disrupts the beam detect circuit. The most common cause of arcing is a bad connection to the transfer roller.
41.2 Error Code on HP Laser Printers

The arcing occurs in the toner/transfer area, and can be caused by a defective toner cartridge, bad high voltage or ground connections to the toner cartridge or transfer roller, or a defective high voltage power supply.

Error code 41 usually occurs whenever users attempt to print a document or picture and usually occurs when certain changes are made to Windows. For example, users might have installed the wrong drivers, or the responsible service is not running.
If you are seeing the 41.3 error on a LaserJet 4, 4Plus, or 5 series printer, and you find a blank sheet of paper in the path, your printer is probably having a failure with the solenoid on the paper feed assembly. This is becoming a common issue as these printers get older.
In some cases the reason for error code 41.7 is that the rollers grabbing fresh paper are not sticky enough any more. In this case I used spray for climbing skins (e.g. colltex) to make them stickier again, and the problem was resolved.
When a 50.22. 00 or a 50.22. 11 error displays on the control panel, it indicates an issue with the fuser warming up.
63.00. 41 There is an error in the toner supplied to the black developer. HP LaserJet Black Developer Unit: 8JM70-67001 (E783xx series) or JC96-11666A (E778xx series}. If the firmware bundle installed on the printer is lower than 4.6.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
What is Error Code 41? Error Code 41 is a common error message that you might encounter when trying to stream content on the platform. This error code indicates that the content you are trying to stream is not available, often due to surge in traffic to a particular title.
The event 41 kernel power means that there is something happened unexpectedly that blocked Windows from turning off properly and there is a message saying that “The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly.”
The warning “The system has rebooted without cleanly shutting down first” is associated with the event 41 kernel power, which indicates that something unexpected occurred that prevented Windows from going off properly. The system could experience this error if it abruptly crashed, stopped responding, or lost power.
Error code 41 is one of several Device Manager error codes. It`s caused either by a hardware device that`s been removed after the driver was loaded or by an issue with the device driver itself.
(Code 41)” This problem occurs if you install a driver for a non-Plug and Play device, but Windows cannot find the device. From Start, search for device manager and select Device Manager from the results. Right-click the device in the list.
41.3 Paper Size Error. HP`s User Guide for the P4014, P4015 and P4515 printer series says: This is typically caused if two or more sheets stick together in the product or if the tray is not properly adjusted . Reload the tray with the correct paper size.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :
Unknown Printer

Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.

Read Full Q/A … :
Unknown Printer

Scanner error keeps coming up
ANSWER : I am having the same problem with my Epson Workforce 645

Read Full Q/A … :
Unknown Printer

HP CLJ CP 5225 ERROR 55.0601
ANSWER : my printer cp5225 is giving me error code 55.0601 message which i can’t fix please help

Read Full Q/A … :
Unknown Printer

Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.

Read Full Q/A … :
Unknown Printer

HP 9040 MFP Error code
ANSWER : bonsoir

Read Full Q/A … :
Unknown Printer

Density Shutter Error
ANSWER : I’ve never worked on one of those printers, but I have never, ever seen 1 valid solution for printer repair on fixya.com I read the replies there when I need a good laugh. Makes me wonder what the “techs” on that forum actually do for a living. It certainly couldn’t be printer repair.

Read Full Q/A … :
Unknown Printer

52.0 SCANNER ERROR
ANSWER : Laser scanner assembly.

Read Full Q/A … :
Unknown Printer