Ink delivery problem from the left ink station.
How to Identify and Fix Common printer Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
The more likley fault is the carriage board. The board is now removeable – so just reverse the whole process one this is done and boot the printer. You can check if the fault is cleared by booting once all the cables are in place – you dont need to re asseble the whole machine.
System error 22:10
The possible cause could be: Reading, writing or initializing the backup EEROM failed. One of the out-of-ink sensors (located in the Ink Supply Station) is not reporting what it should during the initializing process while depressurizing.
The system error 24:10 is a critical error in which the printer cannot be used until has been corrected. Turn the printer on in Diagnostic Mode. Turn On the printer holding down Power + Cancel + DOWN buttons until you hear one beep before releasing ALL three keys.
The 23:10 error code is an air pressurization failure and can be caused from faulty ink cartridges. Turn the power off at the back of the printer and then remove all ink cartridges. Carefully inspect each ink cartridge and make sure you do not see any issues.
If the error reoccurs , check for any ink leakages in the ISS and may need to replace the ISS. If there is no error and plotter prompts for missing ink cartridges , check the use by date on the ink catridge ( if expired – used new ink cartridge). Recommend to use Genuine HP Supplies to avoid damage.
The printer is unable to read the toner cartridge data. The toner cartridge is present but defective. When this error occurs, a question mark appears on the gas gauge of the supply or supplies with the error.
computer we`re going to talk about the error code 22 : 10 or designjet 800 and 500 they`re the same error code and the same fix the error code code indicates that the the printer doesn`t like what it`s seeing with the ink supply station exploitation is on the right side of the machine.
The 21:10 error can be caused by anything that inhibits the service station motion. The best way to troubleshoot the service station is to remove the motor and operate the white gears with your fingers to see if there is any obstruction to the movement of the sled with the 4 print head caps on it.
Problem description:
Curing resistor 2 disconnected or damaged.
Problem Description: Trailing Cable does not seem to be detected. Corrective Action: 1. Switch the Power OFF from the back of the Printer and disconnect the Power cord.
When a 50.22. 00 or a 50.22. 11 error displays on the control panel, it indicates an issue with the fuser warming up.
10.23.15
Install Fuser kit The fuser is either not installed, or not correctly installed in the printer.
When a 30.03.22 error is displayed on the control panel, it indicates that there is an error calibrating the scanner. Turn the printer off, and then back on to clear the error. If the issue continues, contact HP technical support to perform more complex troubleshooting steps.
ERROR 21 11 –
PROBLEMA CON LA SERVICE STATION DEL PLOTTER Solución error 21:11: sustituir la service station (limpiar service y comprobar todos los contactos del plotter). Si necesita que un técnico especializado repare su plotter le ofrecemos un servicio in situ para que no tenga que mover su plotter.
Code 10 “
This device cannot start.
If the hardware key does not contain a “FailReasonString” value the message above is displayed. In the device`s Properties dialog box, click the Driver tab, and then click Update Driver to start the Hardware Update Wizard. Follow the instructions to update the driver.
-12 No Brother printer found. -15 Printer status retrieval failed. -19 While printing, replace the paper cassette. -22 No paper cassette found during a printing operation.
if you get an error code on your 500 or 800 that`s an O one coulomb 10 that`s almost a for sure sign that your electronics module has draw died. there are some other error codes a 111 which means that the fan. has stopped working and you may want to try to replace the fan.
System Error Code 05:10 indicates a Formatter or HPGL/2 Card failure.
The 21:10 error can be caused by anything that inhibits the service station motion. The best way to troubleshoot the service station is to remove the motor and operate the white gears with your fingers to see if there is any obstruction to the movement of the sled with the 4 print head caps on it.
ERROR 21 11 –
PROBLEMA CON LA SERVICE STATION DEL PLOTTER Solución error 21:11: sustituir la service station (limpiar service y comprobar todos los contactos del plotter). Si necesita que un técnico especializado repare su plotter le ofrecemos un servicio in situ para que no tenga que mover su plotter.
Make sure that the Service Station path is clear. Remove any visible obstacles (screws, plastic parts, etc.) restricting the movement of the Service Station. If the carriage has stopped over the service station, on the right side of the product, check that the cutter is not activated.
ERROR 21 11 –
PROBLEMA CON LA SERVICE STATION DEL PLOTTER Solución error 21:11: sustituir la service station (limpiar service y comprobar todos los contactos del plotter). Si necesita que un técnico especializado repare su plotter le ofrecemos un servicio in situ para que no tenga que mover su plotter.
if you get an error code on your 500 or 800 that`s an O one coulomb 10 that`s almost a for sure sign that your electronics module has draw died. there are some other error codes a 111 which means that the fan.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.