Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Small fragments of sticky label material commonly get torn off and stuck within your printer, collecting dust and causing a jam. Shut the printer off, get a flashlight, and try to see inside. Make sure no label fragments have jammed up your printer before proceeding.
If your paper jams are happening randomly and you can`t identify the cause, it could be that your printer rollers are dirty. Over time, dust and debris can build up on the rollers and cause the rollers to grab onto paper unevenly, which can lead to paper jams.
Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Clean the rollers inside the printer, and then try to print again.
Make sure your paper meets the specifications for your product. If paper dust builds up on the rollers, they may lose traction and become unable to feed paper properly. Clean the paper guide. If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
Common cardstock printing problems

If your media is too thick it could cause paper jams as the printer won`t be able to handle it. Your printer may only be able to handle cardstock via a specific tray or sometimes a manual feed, using the wrong tray could also cause jams or mis-prints.

Creases and folds in the paper are normally due to one of the following conditions: The paper is not correctly loaded in the paper tray. You are printing on a special type of paper or other media. The paper has absorbed too much moisture from the surrounding air.
Creases and folds in the paper are normally due to one of the following conditions: The paper is not correctly loaded in the paper tray. You are printing on a special type of paper or other media. The paper has absorbed too much moisture from the surrounding air.
Creases and folds in the paper are normally due to one of the following conditions: The paper is not correctly loaded in the paper tray. You are printing on a special type of paper or other media. The paper has absorbed too much moisture from the surrounding air.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Epson printer can't recognize Epson ink cartridge
ANSWER : Hi, my name is Jim.

Read Full Q/A … :
Unknown Printer

Workforce 600 continues to bend corner of paper then jam where the sheet passes through the metal platen at the right side of printer.
ANSWER : Everytime that I have seen that happen it was because there was a small scrap of paper in the paper path on the side of the fold. I have dislodged hundred, if not thousands of them by shoving a thin, flexible plastic stick down the paper path. You can also cut a piece of file folder to size and use that. For small scraps of paper, it is usually stiff enough to clear the obstruction.

Read Full Q/A … :
Unknown Printer

Epson Stylus C90 (Red Light Continuously Blinks)
ANSWER : It looks like General Error occurs. Check for foreign objects inside the printer which may block the movement of printhead carriage, paper feed, etc.

Read Full Q/A … :
Unknown Printer

Epson Stylus Photo T60 paper jam
ANSWER : paper jam

Read Full Q/A … :
Unknown Printer

Epson XP600 Paper Jam
ANSWER : hi Russ .did u find solution for ur problem?? i have the same problem ,how did u fix ur printer ..will be glad if u write me on email [email protected]

Read Full Q/A … :
Unknown Printer

Epson R2400 printer paper jam reports all the time
ANSWER : I would like to second this question. I have the same issue with the media not being detected by the printer. The forwarding wheels squeak more than I would expect. I wonder where the sensor is that it uses to decide if there is paper or not. If I can figure it out I will post the saga here.

Read Full Q/A … :
Unknown Printer

Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :
Unknown Printer

Epson Workforce 600 won't clear paper jam message
ANSWER : In my case, I have a WorkForce 7620 having this problem too, and there is white post on a sliding plastic bar which is the reason of my sorrow. I cannot move it, and it is getting me so desperate, because it makes the print head get stuck. I try to push it down to get the print head to the right position. Then, when I turn on the printer, the print head cannot move. The bar post don’t go down to free the print head and all I got all the time is an error code 0x69 on the screen. I see no paper jam there. Any suggestion, please?

Read Full Q/A … :
Unknown Printer