Epson WorkForce 435

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Make sure your paper meets the specifications for your product. If paper dust builds up on the rollers, they may lose traction and become unable to feed paper properly. Clean the paper guide. If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary.
If your printouts are slanted, try these solutions: Slide the edge guides against the edges of the paper. Select a higher print quality setting in your printer software. Turn off any high speed settings in your product software.
One of the most common causes of paper jams is that the paper has simply not been loaded correctly into the printer paper feed. With this in mind, remove any paper from the tray in order to check for any jams. If you do see some paper jammed, pull each sheet out of the printer slowly until the printer is clear again.
Preventing a printer paper jam

Overfilling the paper tray is frequently causes paper jams. Many printers have sliding mechanisms that allow different types and sizes of paper to be fed into the printer. If the slider is not correctly positioned, it can cause a paper jam.

A paper feed issue can occur for several reasons, such as dusty or contaminated paper rollers, the condition of the paper in the tray, or even issues with the software.
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust. Select one of the following: Auto: automatically adjusts the paper feed setting (takes 9 to 35 minutes to complete); Epson recommends running this option first.
Click Print Quality Tools, and then select Align or Align Printheads. If prompted by the software or printer control panel to scan the Alignment Page, follow the instructions on the page to complete the alignment.
If multiple pages feed at once, remove the paper, fan the edges to separate the sheets, and reload it. If multiple pages continue to feed at once, turn on the Paper Feed Assist Mode setting in the Setup > System Administration > Printer Settings menu. Do not load more than the recommended number of sheets.
Improperly Loading Paper into the Device

Loading paper that is stuck together, frayed, curled or bent can cause a jam. Overloading the paper tray, loading different thicknesses of paper in the tray or using paper that isn`t appropriate for your particular printer can all result in a jammed printer.

Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust. Select one of the following: Auto: automatically adjusts the paper feed setting (takes 9 to 35 minutes to complete); Epson recommends running this option first.
Creases and folds in the paper are normally due to one of the following conditions: The paper is not correctly loaded in the paper tray. You are printing on a special type of paper or other media. The paper has absorbed too much moisture from the surrounding air.
Creases and folds in the paper are normally due to one of the following conditions: The paper is not correctly loaded in the paper tray. You are printing on a special type of paper or other media. The paper has absorbed too much moisture from the surrounding air.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

Epson WorkForce 435

Epson Workforce 600 won't clear paper jam message
ANSWER : In my case, I have a WorkForce 7620 having this problem too, and there is white post on a sliding plastic bar which is the reason of my sorrow. I cannot move it, and it is getting me so desperate, because it makes the print head get stuck. I try to push it down to get the print head to the right position. Then, when I turn on the printer, the print head cannot move. The bar post don’t go down to free the print head and all I got all the time is an error code 0x69 on the screen. I see no paper jam there. Any suggestion, please?

Read Full Q/A … :

Epson WorkForce 435

Error message to load paper and push OK, but not out of paper
ANSWER : Getting started with binary choices, and following a specific time, points transpired due to the procedures which Used to do not. And when I consequently found out what the thing is my accident, I found this web site http://options24.net which many techniques and choose the best for yourself. I think everyone up against this type of problem, thanks for your attention.

Read Full Q/A … :

Epson WorkForce 435

Workforce 600 continues to bend corner of paper then jam where the sheet passes through the metal platen at the right side of printer.
ANSWER : Everytime that I have seen that happen it was because there was a small scrap of paper in the paper path on the side of the fold. I have dislodged hundred, if not thousands of them by shoving a thin, flexible plastic stick down the paper path. You can also cut a piece of file folder to size and use that. For small scraps of paper, it is usually stiff enough to clear the obstruction.

Read Full Q/A … :

Epson WorkForce 435

Paper jam error
ANSWER : Did you actually check for jammed paper? That would be the problem. You can’t reset a paper jam.

Read Full Q/A … :

Epson WorkForce 435

Error Message "Paper out" when paper loaded
ANSWER : Check your paper tray settings as printer may be looking for paper from the manual feed tray on top of printer.

Read Full Q/A … :

Epson WorkForce 435

Paper feeds straight through without printing on an Epson R2400
ANSWER : I was able to get it to print the internal test page by holding down the sheet paper feed button while turning the machine on — then continuing to hold the sheet paper feed button. It took several attempts, feeding a page straight through, but eventually it caught the sheet and printed. So it may be a timing issue as others have mentioned. It could still mean that the feed rollers are worn out. The back side of the large D-shaped feed roller has visible abrasion on it. The abrasion is difficult to see as the roller does not stay with the flat side exposed.

Read Full Q/A … :

Epson WorkForce 435

paper drive wont accept paper
ANSWER : There is probably a small scrap of paper stuck at the left edge of the paper path. The paper hits it and skews to the left. The smaller size bypasses it. You need to shove something stiff, like a piece of file folder, down the paper path and attempt to dislodge it.

Read Full Q/A … :

Epson WorkForce 435