Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If paper does not feed from the rear feed slot, try cleaning the paper guide using an Epson cleaning sheet. Be sure to insert the paper cassette all the way into your product. If multiple pages feed at once, remove the paper, fan the edges to separate the sheets, and reload it.
Small fragments of sticky label material commonly get torn off and stuck within your printer, collecting dust and causing a jam. Shut the printer off, get a flashlight, and try to see inside. Make sure no label fragments have jammed up your printer before proceeding.
Check the paper feed path and ensure there is nothing blocking the feed path; sometimes blowing compressed air through the scanner will help. Please make sure the scanner is powered off before using compressed air.
Check That the Paper Tray Is Full (Not Jammed)

Sometimes, printers are finicky—there may be paper loaded, but if the printer can`t grab hold, it`s going to think it`s empty. Try removing the paper tray, re-aligning the paper, and sliding it back in. In other instances, there may be some paper jammed in the mechanism.

The paper-width guide is pressed against the paper stack too tightly. The paper tray is not completely inserted into the product. The paper settings in the print driver do not match the paper loaded in the paper tray. The rubber paper-feed rollers are dusty.
Adjust the paper guides in the tray to match the size of the paper. Remove the paper, smooth it out, then reload it. If the paper misfeeds, do not use that paper. Remove the moist paper, then replace it with new, dry paper.
Step one: Perform a power reset

Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the rear of the product.

The paper source settings or tray settings change when you select a different printer in Word. The paper source settings or the tray settings change when you try to print a document in Microsoft Word. Note This behavior is not specific to Word.
Set the size and type of paper to be loaded in each paper source. Access Web Config and select the Print tab > Paper Source Settings.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
There are different methods of paper feeding. With dot matrix printers, paper is often feed through pins on a wheel that grab and slowly move paper through the printer. With inkjet and other page printers, paper is fed through the printer with rollers that grab and move the paper through the printer.
The Print Spooler is software built into the Windows operating system that temporarily stores print jobs in the computer`s memory until the printer is ready to print them. In some circumstances you may need to stop and/or restart the service.
Your Epson printer may have failed to recognize the new ink cartridge, or its ink level system has read it as empty. For numerous Epson printer models, there`s a way to bypass this built-in ink checking system through a quick cartridge reset. Raise the printer`s top cover and then hold the Ink button.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :
Unknown Printer

Epson Stylus Photo T60 paper jam
ANSWER : paper jam

Read Full Q/A … :
Unknown Printer

Epson Stylus C64 in problems, Help!!!!
ANSWER : a lucky tip – if all else fails and you don’t have a PC instead of a Mac, try what I did on my C63. When the head finished moving and both red lights flashed with a “general error’ message, turn off the printer power supply and physically slide the head from its rest position to the far left of the printer. This seems to re-set the “foreign body” trigger. Turn the power back on, the head slowly moves back to the rest position and hey presto the lights have stopped flashing and the printer works! Sounds clumsy but you have nothing to lose trying it, the cost of repair exceeds the value of a 10 year old printer.

Read Full Q/A … :
Unknown Printer

Paper feeds straight through without printing on an Epson R2400
ANSWER : I was able to get it to print the internal test page by holding down the sheet paper feed button while turning the machine on — then continuing to hold the sheet paper feed button. It took several attempts, feeding a page straight through, but eventually it caught the sheet and printed. So it may be a timing issue as others have mentioned. It could still mean that the feed rollers are worn out. The back side of the large D-shaped feed roller has visible abrasion on it. The abrasion is difficult to see as the roller does not stay with the flat side exposed.

Read Full Q/A … :
Unknown Printer

Epson Stylus Photo R230 – flashing red lights fix
ANSWER : REDLIGHT

Read Full Q/A … :
Unknown Printer

EPSON Stylus NX400 Vista Print Problem
ANSWER : I have the similar issue. The browse button would not open the connection listing the shared printer. How can I fix it? Please respond to this post or contact me via buy essays. Thank you in advance!

Read Full Q/A … :
Unknown Printer

Epson Stylus Photo R230(2 red indicator blinking)
ANSWER : 2 red indicator blinking

Read Full Q/A … :
Unknown Printer

epson stylus photo 2000p problems
ANSWER : plz i just receive epson stylus photo 2000p from a friend and the ink light are on nothing is working plz help

Read Full Q/A … :
Unknown Printer