Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Remove the cartridges from your printer – switch your printer off. Using a piece of damp kitchen roll, gently wipe the copper plate on the cartridge. Allow the chips to air dry. Once the chips are completely dry, re-install the cartridges into your printer and switch the printer back on.
Remove all of the new cartridges you had installed and re-install the old (empty) cartridges that worked. Restart the printer, this should remove the not recognised error (and tell you some are empty).
Hey, you can reset Epson ink cartridge without resetter! As shown above, you can reset Epson chips by pressing and holding the button above the chip with a bent paper clip for 10 seconds.
Clean the Cartridge Contacts: one of the most common reasons you might get a cartridge problem error when your cartridges are new and full is the contacts on the cartridge might be dirty or otherwise obscured from making good contact with the electronics in the printer head carriage.
The most common reason a refilled ink cartridge does not work is that you didn`t reinstall the cartridge properly. Check the cartridge and make sure it is not dislodged or misaligned. If there is no visible sign of misinstallation, remove the cartridge and reinstall it.
Verify the ink cartridge(s) is inserted properly. Some cartridges snap in place, and if they are not inserted fully, the printer won`t print anything. If a lever is moved from its original position to allow for installation of ink cartridges, ensure it is returned to its original position.
Yes, you can reset the print settings to their original, default values. Press and hold down the Cancel button for 3 seconds. When the message to reset the printer to default settings appears, press OK to reset the print settings.
The chip in question tells the printer when toner levels are getting low. A useful feature, certainly, but one that printer companies often use to lock out third-party cartridges—without the chip, the printer will say it doesn`t know how much ink or toner is inside the cartridge, assume it`s zero, and refuse to print.
Press the button on the chip-reset tool for several seconds until the LED light on the device goes off. Then, unlock the reset tool from the cartridge. Use the resetter with other cartridges and install them back into the corresponding slots in your printer. Voila!
What should I do? The ink cartridges may not have been installed using the correct procedure or they may not be seated correctly. Follow the instructions below to correctly install and reseat the ink cartridges. Turn on your product.
Yes, you can reset the print settings to their original, default values. Press and hold down the Cancel button for 3 seconds. When the message to reset the printer to default settings appears, press OK to reset the print settings.
It is usually on the top right-hand side of your printer, near any digital display screen that the printer may have, and where the button used to turn the computer on and off is also located. Find the button marked Pause/Reset on the row of buttons on the control panel.
Press the button on the chip-reset tool for several seconds until the LED light on the device goes off. Then, unlock the reset tool from the cartridge. Use the resetter with other cartridges and install them back into the corresponding slots in your printer. Voila!

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Epson Stylus Photo T60 paper jam
ANSWER : paper jam

Read Full Q/A … :
Unknown Printer

Epson printer can't recognize Epson ink cartridge
ANSWER : Hi, my name is Jim.

Read Full Q/A … :
Unknown Printer

Epson Stylus Photo R230 – flashing red lights fix
ANSWER : REDLIGHT

Read Full Q/A … :
Unknown Printer

epson stylus photo 2000p problems
ANSWER : plz i just receive epson stylus photo 2000p from a friend and the ink light are on nothing is working plz help

Read Full Q/A … :
Unknown Printer

EPSON Stylus NX400 Vista Print Problem
ANSWER : I have the similar issue. The browse button would not open the connection listing the shared printer. How can I fix it? Please respond to this post or contact me via buy essays. Thank you in advance!

Read Full Q/A … :
Unknown Printer

Epson Stylus C64 in problems, Help!!!!
ANSWER : a lucky tip – if all else fails and you don’t have a PC instead of a Mac, try what I did on my C63. When the head finished moving and both red lights flashed with a “general error’ message, turn off the printer power supply and physically slide the head from its rest position to the far left of the printer. This seems to re-set the “foreign body” trigger. Turn the power back on, the head slowly moves back to the rest position and hey presto the lights have stopped flashing and the printer works! Sounds clumsy but you have nothing to lose trying it, the cost of repair exceeds the value of a 10 year old printer.

Read Full Q/A … :
Unknown Printer

Epson Stylus Photo R230(2 red indicator blinking)
ANSWER : 2 red indicator blinking

Read Full Q/A … :
Unknown Printer

Multiple Problems With Epson Stylus Photo R280
ANSWER : I have had my R280 for about 3 years. It has worked fine with generic cartridges for several years now. Last week it indicated I needed to replace one cartridge. I used a generic cartridge from the same manufacturer I had used before. The printer would not accept the new cartridge and now told me that I needed to replace 4 cartridges because it recognized them as non Epson. Surely there is some way to fool the printer so it does not recognize generic cartridges – which have worked well in the past and are still over half full! Anyone got any ideas?

Read Full Q/A … :
Unknown Printer