Epson Stylus Photo Stylus Photo

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

The product is busy. Wait for the power light to stop flashing before turning off the product. If you just replaced an ink cartridge and the power light is still flashing after 3 minutes, the cartridge may be installed incorrectly.
When the red H ink light flashes, one or more ink cartridges are low on ink. When the red H ink light stays on, you need to replace the cartridge(s). When you print, you`ll also see a message on your screen telling you which cartridge is low or empty.
Ink and paper lights blinking alternately means that your internal “waste ink pads” are full and need resetting/cleaning out. Check your Epson Status Monitor (on PC) for any error messages – if it says “service required” or “… end of service life” then it`s the waste pads.
The Power light blinks at a steady interval when the printer is processing a print job. If the Power light blinks fast, the ink cartridge door might be open, or the printer might be in an error state. If an error message displays on the computer screen, follow the on-screen messages to resolve the issue.
There are two indicator lights on the printer: the Status light and the Charging light. Each indicator light shows the status of the printer as described below. Status indicator light: A blue or green light indicates the printer is operating correctly, while red indicates an error has occurred. Indicator light color.
An ink cartridge is low. Make sure you have a replacement cartridge.
The orange !

If the printer`s orange exclamation light is lit, it usually means there is a paper jam or the cover is open. Open the printer`s cover and make sure the paper is not jammed. Close the printer`s cover. Turn the printer off, then back on.

If the scanner light is still flashing red, the scanner may be malfunctioning, or the scanner light source may need to be replaced. Contact Epson for details.
Answer: Red light blinking in L220 printer means the printer may have roller jam problem OR sensor problem occurs. So, please check for roller jam and fix it. Second, check the sensor`s head and clean it too. If you can`t do it manually, then check out the following video tutorial.
Ink has run out. (The lamp on the ink tank flashes.) If printing is in progress, stop printing, replace the ink tank, and then print again. Printing under the current condition may damage the printer.
Eight flashes:Ink absorber is almost full

The ink absorber is almost full. Press the printer`s RESUME/CANCEL button to continue printing. Contact the service center.

When you see a flashing light by data that means that a print job has been released to that printer but is still processing. This typically happens when someone is printing a larger file size job.
Look for an Ink drop icon ( or ), a Cartridge icon , an Ink Levels menu, or a Toner Level indicator.
If your Epson printer is printing out faint images, skipping lines, or is streaking your image with lines, chances are you have a clogged nozzle–a common problem many users have with Epson printers. It`s unavoidable that print heads clog over time as small amounts of ink residue dry up and collect in the nozzles.
The ink levels may be low and you may need to refill the ink. Visually check the ink levels. Also make sure you filled the tanks with the correct colors of ink. After you print, the colors in your printout need time to set as the ink dries.
To remove dust or smudges, gently wipe the obstacle sensor glass with lens-cleaning paper. To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the obstacle sensor glass. Warning: Do not use a lens cleaner that contains flammable gas.
Paper may be jammed in the product. Remove any jammed paper, and press the cancel button to clear the error. If the lights still flash, there may be a product error. Turn the product off, check inside for jammed paper or foreign objects, then turn the product back on.
Red ink light flashes One of the cartridges is low on ink. Check the message that appears on your screen to determine which cartridge is low. Make sure you have a replacement cartridge. Red ink light is on One of the cartridges is out of ink or not installed.
An ink pad is nearing or at the end of its service life. Contact Epson for support.
Yes, you can reset the print settings to their original, default values. Press and hold down the Cancel button for 3 seconds. When the message to reset the printer to default settings appears, press OK to reset the print settings.
When the red light starts blinking, then there can be many issues which it indicates, but majorly it suggests resetting the ink and replenishing degree. The printer might be out of ink, or it is unable to identify ink cartridge but fixing it is easy and do not require any technical knowledge.
Press the home button, if necessary. Press the left or right arrow button to select Maintenance > Reset Ink Level. Press the start button, the OK button twice, and then the start button again. Press the right or left arrow button to highlight the ink tank you refilled and press the OK button to select it.
Power Ink Flushing affects the service life of the ink pads by causing them to reach their capacity sooner. When an ink pad reaches the end of its service life, the product stops printing and you must contact Epson for support. Flushing the Ink Using a Computer Utility.
The ink is running low. Prepare a new ink cartridge.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Epson Stylus Photo R230(2 red indicator blinking)
ANSWER : 2 red indicator blinking

Epson Stylus Photo R230 – flashing red lights fix
ANSWER : REDLIGHT

Epson Stylus Photo T60 paper jam
ANSWER : paper jam

Multiple Problems With Epson Stylus Photo R280
ANSWER : I have had my R280 for about 3 years. It has worked fine with generic cartridges for several years now. Last week it indicated I needed to replace one cartridge. I used a generic cartridge from the same manufacturer I had used before. The printer would not accept the new cartridge and now told me that I needed to replace 4 cartridges because it recognized them as non Epson. Surely there is some way to fool the printer so it does not recognize generic cartridges – which have worked well in the past and are still over half full! Anyone got any ideas?

epson stylus photo 2000p problems
ANSWER : plz i just receive epson stylus photo 2000p from a friend and the ink light are on nothing is working plz help

Epson Stylus Photo RX600, porous pad
ANSWER : Hi, You may have by now (Feb.2016 ) solved your problem, if not I have just used to code to reset my copy counter but as yet have not replaced the surplus ink pad tanks, what I am going to do is install an external surplus ink tank to bypass the pads as I am a bit nervous of taking my printer apart, Go to ebay and type in “RX600 surplus external ink tank” cost is well worth it, Happyhammer 20.02.16

Epson stylus photo R300
ANSWER : Had the same problem with the VM cartridge, I cleaned and put it back several times not luck,then the MK started acting up as well, cleaned it and put it back and worked, the VM however was still acting up. I turned the printer off and took out the VM and put it back without cleaning, turned on the printer and the VM is working now….come on Epson what the hell is wrong with this system.

Epson Stylus Photo R200 – flashing red lights
ANSWER : The R800 will flash the ink and paper lights alternately when the ink pads are assumed to be full from extensive head cleaning. Sometimes, if not always, the head will lock into place on the right side above the ink head cleaning sponges that release ink to the lower ink pads.To correct the problem you need to clean the sponge area, I use cotton swabs. If the head is locked to need to release the carriage lock with a screwdriver. This will require removing the cover, but not necessarily the bottom of the unit.There is a 179 page service manual available for download for $16.50. There are free downloads of this manual, but usually are missing the 100 pages.You can remove the cover by:1. Remove the three screws on the rear housing (One to the left of the power plug, one on the opposite side and one in the lower middle bottom.2. Remove the three screws inside the upper housing (Just under the lid where the hinge is).3. Remove the screw under the left and right side in back below the vents.4. In the back pull the white ribbon closest to you out of the block, do not try to remove the block itself.5. Place a screwdriver into the slot both on the right and lift of the bottom corners on the back to release the hooks that hold the upper unit.6. Lastly, put a screwdriver into the notches on the bottom of the printer located in the front right and left, they are spring loaded.7. Remove cover.8. The head lock release screw is in the right side of the printer and is partially covered by the lower housing. I drilled a half inch hole into the side as to be able to insert a screwdriver. Turn the screw to the left and the head will rise out of the locked position. You only need to turn enough to release the head.9. Clean the sponges and any areas you see with excess ink.10. Place the cover on the unit enough to plug the white ribbon back in and turn the unit on.If the printer lights stop flashing then you are all set.