Epson Stylus Photo EX

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

There are a number of reasons why this might happen. In a large number of cases we come across, the photo paper weight (which is measured in GSM) or overall thickness exceeds the printer`s ability meaning it is too think or too heavy for the rollers to successfully handle.
Make sure the USB cable is connected securely at both ends and meets the requirements. Run a printer check. If the test page prints, make sure your software is installed correctly. Make sure the printer cover is closed.
Your Epson printer may have failed to recognize the new ink cartridge, or its ink level system has read it as empty. For numerous Epson printer models, there`s a way to bypass this built-in ink checking system through a quick cartridge reset. Raise the printer`s top cover and then hold the Ink button.
The photo tray is overloaded. The paper is curled. The print side, or shiny side, of the paper is not loaded in the tray face down. The paper width guide is too tight against the paper stack.
Try removing the paper tray, re-aligning the paper, and sliding it back in. In other instances, there may be some paper jammed in the mechanism. Usually your printer will tell you so, and you just need to open the access panel and pull the crumpled paper out.
1: Check Printer Power, Cables, and Paper

Check that the correct paper is properly loaded into the printer and is not jammed. Replacing damaged cables, plugging in loose or disconnected cables, and fixing paper jams as necessary may resolve the issue.

If you have problems feeding paper, try these solutions: If paper does not feed for printing, remove it from the rear feed slot or cassette. Reload it, then adjust the edge guides. Make sure the paper stack is not above the tab on the edge guides inside the cassette or rear feed slot.
As a rule of thumb, to achieve photo quality print, you will need to use an image resolution of 300 pixels per inch. We write this as 300 DPI and means that in each inch of your print there will be 300 pixels.
Some of the most common printer problems that most of us have experienced include paper jamming, slow printing, uneven printing, and wrong colour output. If you use your printer frequently, we know how annoying it can be to have persisting problems with the printer.
Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.
A1: When an Epson printer is in an error state, it indicates that there is a problem or issue preventing the printer from functioning properly. It could be due to various reasons such as paper jams, connectivity issues, software conflicts, or low ink levels.
If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.
Reset. Resetting the printer stops printing and clears the current print job received from the active interface. You may want to reset the printer when there is a problem with the print job itself and the printer cannot print successfully.
1. On the printer display home screen, select the “set up” button (it looks like a gear). 2. Select “settings” > “device settings” > “reset settings” > “reset all” > “OK” and then “Yes.”
Hey, you can reset Epson ink cartridge without resetter! As shown above, you can reset Epson chips by pressing and holding the button above the chip with a bent paper clip for 10 seconds.
In short, yes, laser printers can print on glossy coated paper. As long as the right type of paper is used to allow the toner to fuse with it, great printing results on glossy paper can be achieved with any laser printer.
Glossy Paper

This paper can be used to print photographs or vibrant images, but it does have a much longer dry time than regular paper, so you might experience some smudges if handled incorrectly. As a best practice, it`s best to only print glossy paper with a laser printer.

Make sure the paper is not curled or folded. If so, flatten it or curl it slightly toward the opposite side before loading. Remove the stack of paper and make sure that the paper is not too thin. Fan the edges of the stack to separate the sheets, then reload the paper.
For printing, the recommended resolution for all images and art files is 300 dpi. The offset press cannot accurately reproduce resolutions above 300, so it is the industry standard.
There are numerous possible causes for a printer that`s randomly producing blanks. The most common ones are empty ink cartridges, improper cartridge installation, and congested nozzles. Driver and software issues can sometimes cause this problem as well.
The reset key is a single use key and once used cannot be used again. All EPSON printers have inbuilt counters that count up the number of pages a printer produces, the number of head cleans executed and various other attributes. Once a critical level is reached the printer will enter its service mode.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Epson Stylus Photo R230 – flashing red lights fix
ANSWER : REDLIGHT

Read Full Q/A … :

Epson Stylus Photo EX

Epson Stylus Photo T60 paper jam
ANSWER : paper jam

Read Full Q/A … :

Epson Stylus Photo EX

Epson Stylus Photo R230(2 red indicator blinking)
ANSWER : 2 red indicator blinking

Read Full Q/A … :

Epson Stylus Photo EX

Epson R320 Photo Printer Won't Print Black Ink
ANSWER : Megan !!!! YEAH!!! Mine is a WrokForce 845 and mine are refillables for years. Refilled the BLACK and it quit. 20 nozzle checks later and still nothing so I took a syringe with a piece of fish air tubing. pulled all the 4 cartridges and blew air into all colors, cleaned the contacts and two cleanings and WALLAAA!!! Prints great.

Read Full Q/A … :

Epson Stylus Photo EX

epson stylus photo 2000p problems
ANSWER : plz i just receive epson stylus photo 2000p from a friend and the ink light are on nothing is working plz help

Read Full Q/A … :

Epson Stylus Photo EX

Epson stylus photo R300
ANSWER : Had the same problem with the VM cartridge, I cleaned and put it back several times not luck,then the MK started acting up as well, cleaned it and put it back and worked, the VM however was still acting up. I turned the printer off and took out the VM and put it back without cleaning, turned on the printer and the VM is working now….come on Epson what the hell is wrong with this system.

Read Full Q/A … :

Epson Stylus Photo EX

Epson Stylus Photo RX600, porous pad
ANSWER : Hi, You may have by now (Feb.2016 ) solved your problem, if not I have just used to code to reset my copy counter but as yet have not replaced the surplus ink pad tanks, what I am going to do is install an external surplus ink tank to bypass the pads as I am a bit nervous of taking my printer apart, Go to ebay and type in “RX600 surplus external ink tank” cost is well worth it, Happyhammer 20.02.16

Read Full Q/A … :

Epson Stylus Photo EX

Multiple Problems With Epson Stylus Photo R280
ANSWER : I have had my R280 for about 3 years. It has worked fine with generic cartridges for several years now. Last week it indicated I needed to replace one cartridge. I used a generic cartridge from the same manufacturer I had used before. The printer would not accept the new cartridge and now told me that I needed to replace 4 cartridges because it recognized them as non Epson. Surely there is some way to fool the printer so it does not recognize generic cartridges – which have worked well in the past and are still over half full! Anyone got any ideas?

Read Full Q/A … :

Epson Stylus Photo EX