Epson Stylus Photo 2000P

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If you notice white or dark lines in your prints (also called banding), try these solutions before you reprint: Run a nozzle check to see if any of the print head nozzles are clogged. Then clean the print head, if necessary. Make sure the paper type setting matches the type of paper you loaded.
Streaks and unwanted lines could mean that the printer heads are out of alignment. There`s an alignment tool in the printer`s control panel. If that`s not the issue then the printer is dirty. Printer ink stripes may appear along the edges of the paper, which means there`s ink on the rollers and other parts.
A printer printing lines on the page are normally caused by a blocked, dirty, or damaged print head. Blocked ink cartridge nozzles, or not removing protective seals correctly when you installed a new ink cartridge can also cause missing lines of print.
If your printer is printing in blue it is out of yellow ink. and if only cyan or light blue is printing red is also over. Get your cartridge replaced or refilled the printer will start printing properly.
If your printouts are blurry or smeared, try these solutions: Make sure your paper is not damp, curled, old, or loaded incorrectly in your product. Slide the edge guides to the edges of the paper. Use a support sheet with special paper, or load special paper one sheet at a time.
Horizontal lines across prints are most commonly experienced with inkjet printers and are usually down to a partially blocked printhead. Inkjet printers from many different manufacturers are prone to this including machines by Brother, Canon, Epson, Dell, Hewlett Packard (HP), Kodak, Lexmark and many more.
Vertical lines in prints are an early warning sign of a low ink cartridge, which may show up before the printer`s low ink alerts start. You can fix the problem by replacing the low cartridge. Gently shaking the drained cartridge a bit may help to get another few prints out of it without vertical lines.
Double printing can occur for several possible reasons including an improperly seated ink tank, a misaligned print head, and a dirty encoder stip. Select one of the links below to get detailed instructions to address the issue. Check that all ink tanks are seated properly. Refer to Replace an ink tank.
Streaking is usually caused by a worn out drum unit or spent toner cartridge. Drum units are a consumable and only need to be replaced after the use of 3 or 4 toners. Not all printers use a separate toner and drum unit.
If your Epson printer is printing out faint images, skipping lines, or is streaking your image with lines, chances are you have a clogged nozzle–a common problem many users have with Epson printers. It`s unavoidable that print heads clog over time as small amounts of ink residue dry up and collect in the nozzles.
What should I do? If your printouts contain misaligned vertical lines, you may need to run the print head alignment utility from the driver to align the print head. Your printer must be connected to a local port, not on a network, to use the Print Head Alignment utility.
If the quality of your printouts remains poor even after repeatedly cleaning and aligning the print head, one or some of the ink cartridges may be old or damaged and should be replaced. To replace an ink cartridge before the Status Monitor notifies you that the cartridge is empty, see Replacing an Ink Cartridge.
Vertical lines in prints are an early warning sign of a low ink cartridge, which may show up before the printer`s low ink alerts start. You can fix the problem by replacing the low cartridge. Gently shaking the drained cartridge a bit may help to get another few prints out of it without vertical lines.
Digital noise causes most cases of vertical lines. More specifically, it is due to the `grid noise,` as well as `read noise. ` Not understanding the basics, like ISO setting, can lead to vertical lines appearing in image files.
White lines will typically start appearing on your print outs due to a clogged up printer head. Your first port of call when solving this problem is to run the cleaning program on your printer, which should be accessible through its settings menu.
Digital noise causes most cases of vertical lines. More specifically, it is due to the `grid noise,` as well as `read noise. ` Not understanding the basics, like ISO setting, can lead to vertical lines appearing in image files.
White lines will typically start appearing on your print outs due to a clogged up printer head. Your first port of call when solving this problem is to run the cleaning program on your printer, which should be accessible through its settings menu.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Epson Stylus Photo T60 paper jam
ANSWER : paper jam

Read Full Q/A … :

Epson Stylus Photo 2000P

Epson Stylus Photo R230 – flashing red lights fix
ANSWER : REDLIGHT

Read Full Q/A … :

Epson Stylus Photo 2000P

Epson Stylus Photo R230(2 red indicator blinking)
ANSWER : 2 red indicator blinking

Read Full Q/A … :

Epson Stylus Photo 2000P

Multiple Problems With Epson Stylus Photo R280
ANSWER : I have had my R280 for about 3 years. It has worked fine with generic cartridges for several years now. Last week it indicated I needed to replace one cartridge. I used a generic cartridge from the same manufacturer I had used before. The printer would not accept the new cartridge and now told me that I needed to replace 4 cartridges because it recognized them as non Epson. Surely there is some way to fool the printer so it does not recognize generic cartridges – which have worked well in the past and are still over half full! Anyone got any ideas?

Read Full Q/A … :

Epson Stylus Photo 2000P

epson stylus photo 2000p problems
ANSWER : plz i just receive epson stylus photo 2000p from a friend and the ink light are on nothing is working plz help

Read Full Q/A … :

Epson Stylus Photo 2000P

Epson Stylus Photo RX600, porous pad
ANSWER : Hi, You may have by now (Feb.2016 ) solved your problem, if not I have just used to code to reset my copy counter but as yet have not replaced the surplus ink pad tanks, what I am going to do is install an external surplus ink tank to bypass the pads as I am a bit nervous of taking my printer apart, Go to ebay and type in “RX600 surplus external ink tank” cost is well worth it, Happyhammer 20.02.16

Read Full Q/A … :

Epson Stylus Photo 2000P

Epson stylus photo R300
ANSWER : Had the same problem with the VM cartridge, I cleaned and put it back several times not luck,then the MK started acting up as well, cleaned it and put it back and worked, the VM however was still acting up. I turned the printer off and took out the VM and put it back without cleaning, turned on the printer and the VM is working now….come on Epson what the hell is wrong with this system.

Read Full Q/A … :

Epson Stylus Photo 2000P

Epson Stylus Photo R200 – flashing red lights
ANSWER : The R800 will flash the ink and paper lights alternately when the ink pads are assumed to be full from extensive head cleaning. Sometimes, if not always, the head will lock into place on the right side above the ink head cleaning sponges that release ink to the lower ink pads.To correct the problem you need to clean the sponge area, I use cotton swabs. If the head is locked to need to release the carriage lock with a screwdriver. This will require removing the cover, but not necessarily the bottom of the unit.There is a 179 page service manual available for download for $16.50. There are free downloads of this manual, but usually are missing the 100 pages.You can remove the cover by:1. Remove the three screws on the rear housing (One to the left of the power plug, one on the opposite side and one in the lower middle bottom.2. Remove the three screws inside the upper housing (Just under the lid where the hinge is).3. Remove the screw under the left and right side in back below the vents.4. In the back pull the white ribbon closest to you out of the block, do not try to remove the block itself.5. Place a screwdriver into the slot both on the right and lift of the bottom corners on the back to release the hooks that hold the upper unit.6. Lastly, put a screwdriver into the notches on the bottom of the printer located in the front right and left, they are spring loaded.7. Remove cover.8. The head lock release screw is in the right side of the printer and is partially covered by the lower housing. I drilled a half inch hole into the side as to be able to insert a screwdriver. Turn the screw to the left and the head will rise out of the locked position. You only need to turn enough to release the head.9. Clean the sponges and any areas you see with excess ink.10. Place the cover on the unit enough to plug the white ribbon back in and turn the unit on.If the printer lights stop flashing then you are all set.

Read Full Q/A … :

Epson Stylus Photo 2000P