Epson Stylus C20UX

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If paper does not feed from the rear feed slot, try cleaning the paper guide using an Epson cleaning sheet. Be sure to insert the paper cassette all the way into your product. If multiple pages feed at once, remove the paper, fan the edges to separate the sheets, and reload it.
Dust, paper fiber, and other debris might accumulate on the pick rollers and cause paper feed issues. To help prevent paper feed issues, clean the rollers inside the printer and in the duplexer (if equipped). If the other steps in this document fail to resolve the issue, then reset the printer.
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust. Select one of the following: Auto: automatically adjusts the paper feed setting (takes 9 to 35 minutes to complete); Epson recommends running this option first.
Check the paper feed path and ensure there is nothing blocking the feed path; sometimes blowing compressed air through the scanner will help. Please make sure the scanner is powered off before using compressed air.
Misfeeds occur frequently. The number of sheets loaded exceeds the capacity of the printer. Load paper only as high as the upper limit markings on the side fences of the paper tray, or the markings on the paper guides of the bypass tray. Misfeeds occur frequently.
Document specifications. The Automatic Document Feeder (B81321 ) allows you to automatically load multi-page documents into your scanner. This is useful for OCR (optical character recognition) scanning, or for creating an image database or PDF files.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
If a Firewall on your computer is active, it may be rejecting the necessary network connection needed for the network scanning software to operate properly. Disable the Firewall on your computer and try the network scanning again. Temporarily change your firewall/security settings to allow network connection.
Cause 1: The photo bypass tray is located at the wrong position. Cause 4: Paper dust has accumulated on the surface of the paper pick-up rollers. Cause 6: The paper tray was not fully inserted. NOTE: Illustrations shown below are from a representative product and may differ from your Brother machine.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

Epson Stylus C20UX

Epson Stylus Photo T60 paper jam
ANSWER : paper jam

Read Full Q/A … :

Epson Stylus C20UX

Epson Stylus Photo R230(2 red indicator blinking)
ANSWER : 2 red indicator blinking

Read Full Q/A … :

Epson Stylus C20UX

Paper feeds straight through without printing on an Epson R2400
ANSWER : I was able to get it to print the internal test page by holding down the sheet paper feed button while turning the machine on — then continuing to hold the sheet paper feed button. It took several attempts, feeding a page straight through, but eventually it caught the sheet and printed. So it may be a timing issue as others have mentioned. It could still mean that the feed rollers are worn out. The back side of the large D-shaped feed roller has visible abrasion on it. The abrasion is difficult to see as the roller does not stay with the flat side exposed.

Read Full Q/A … :

Epson Stylus C20UX

Epson Stylus Photo R230 – flashing red lights fix
ANSWER : REDLIGHT

Read Full Q/A … :

Epson Stylus C20UX

Epson Stylus PX810FW
ANSWER : You could have air in the tubing/print head.

Read Full Q/A … :

Epson Stylus C20UX

Need help for Epson Stylus color 3000 print head?
ANSWER : I need help changing the print head in my Epson 3000 – I have 2 printers – one will not stay in alignment and the other black ink is plugged and I have soaked it and cannot get it to budge.

Read Full Q/A … :

Epson Stylus C20UX

Epson Stylus C90 (Red Light Continuously Blinks)
ANSWER : It looks like General Error occurs. Check for foreign objects inside the printer which may block the movement of printhead carriage, paper feed, etc.

Read Full Q/A … :

Epson Stylus C20UX