Epson Stylus CX3200

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Access the printer settings. Click the Main tab, and then make suitable settings. Select plain papers or Envelope as the Paper Type setting. Select Grayscale as the Color setting.
Reasons for Epson printer will not print from computer

Jammed paper. Ink cartridge issue. No paper is installed. Outdated printer driver.

The printer will not operate if a black ink cartridge is expended or any cartridge is removed. If a color cartridge is expended, you may be able to continue printing temporarily with black ink. It`s best to always have extra cartridges on hand.
Ink in a cartridge is low. You can continue printing, or check which cartridge is low and replace it. An ink cartridge is expended or not installed correctly. Replace or reinstall the cartridge.
This is usually caused by a non-flow of ink from the cartridge through the print head. In the case of an ink cartridge with an integrated printed head, take a warm damp cloth and gently wipe it across the print head until you see a flow of ink on the tissue or cloth.
Just above the circuit board on most printer cartridges, you`ll find a small button. You`ve seen these tiny buttons before on cell phones, phone chargers, etc. This is your reset button, and the only way to get in there is either with a paper clip or the tip of a pen (which will leave a tiny ink smudge on the button).
There is a possibility that it didn`t properly click into the designated slot. If this is the case, you should lift the cover and double-check in order to verify that the cartridge is clicked into place. Otherwise, it would not be possible for the printer to detect it.
Can you print with one or two empty ink cartridges? The quick answer is: Yes, you can (if you own a printer model that allows it) — but you shouldn`t keep printing with an empty cartridge for too long.
A typical ink cartridge will yield 250 to 300 pages depending on the color density of the prints. The yield of a typical toner cartridge in a laser printer is between 2,500 and 3,000 pages.
Status indicator light:

A blue or green light indicates the printer is operating correctly, while a red light indicates an error has occurred. A system error has occurred. An error has occurred.

A common cause of faded, faint printouts from your inkjet printer is dried ink particles causing a blockage in your printer. The printheads on an ink cartridge can be become blocked if the printer is not used for a period of time, so it is recommended to print a few pages each month to maintain the print quality.
There are chips inside the original cartridges to record how many pages were printed and they cannot be reset. As a result the printer reads the chips and tells you that the cartridges are empty, even though they are not. This is why you are getting the “ink low” message even though the ink tank is at full capacity.
If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.
Can you use compatible ink in Epson EcoTank printers? Yes, compatible ink bottles can be used with Epson EcoTank printers.
Yes, you can use a compatible or third-party brand of ink in your printer. Lower priced printer cartridges from third-party companies are available for almost every popular printer model and can save printer users thousands on printing costs every year.
Click the start menu and search for `Devices and Printers`. Select devices and printers in the search bar. This will allow you to see the printers connected to the computer. Click the printer you want to check, and you`ll see the ink levels at the bottom of the devices and printers section.
Your Epson printer may have failed to recognize the new ink cartridge, or its ink level system has read it as empty. For numerous Epson printer models, there`s a way to bypass this built-in ink checking system through a quick cartridge reset. Raise the printer`s top cover and then hold the Ink button.
Turn off the ink monitor by checking off the “Disable Epson Status Monitor” found within a box. And lastly, click “Save” and close the window. That`s about it the printer and the cloned ink cartridges can now start printing operation.
Remove the cartridges from your printer – switch your printer off. Using a piece of damp kitchen roll, gently wipe the copper plate on the cartridge. Allow the chips to air dry. Once the chips are completely dry, re-install the cartridges into your printer and switch the printer back on.
Even if you select Black/Grayscale or Grayscale in the printer software, some color ink is still being used. Epson printers contain a permanent print head that needs to be charged with all colors to work. Even when you are printing black text only, a small amount of color ink is used to keep the print head charged.
For Windows:

Go to Control panel and then Devices and Printers. Find and right-click on your printer and click on Printing Preferences. Go to Quick Setup tab and then select Grayscale.

If the ink level is sufficient, but the printer still does not print black ink, you may need to run a cleaning cycle. A cleaning cycle is a process that cleans the printer heads and removes any clogged or dried ink.
Several factors may cause the product to print blank pages, such as print settings, low ink, or the product itself. Check the following: Make sure the product is placed on a flat, stable surface that extends beyond the base in all directions. The product won`t operate properly if it`s tilted or at an angle.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Just installed new epson ink and have red light on
ANSWER : t60 fatal error

Read Full Q/A … :

Epson Stylus CX3200

Epson Stylus C90 (Red Light Continuously Blinks)
ANSWER : It looks like General Error occurs. Check for foreign objects inside the printer which may block the movement of printhead carriage, paper feed, etc.

Read Full Q/A … :

Epson Stylus CX3200

Epson Stylus Photo R230 – flashing red lights fix
ANSWER : REDLIGHT

Read Full Q/A … :

Epson Stylus CX3200

Epson 7880 ink pump sucking ink
ANSWER : Not ink pump, but air pump, to put the ink feed under pressure.

Read Full Q/A … :

Epson Stylus CX3200

Epson printer can't recognize Epson ink cartridge
ANSWER : Hi, my name is Jim.

Read Full Q/A … :

Epson Stylus CX3200

Epson Stylus Photo R200 – flashing red lights
ANSWER : The R800 will flash the ink and paper lights alternately when the ink pads are assumed to be full from extensive head cleaning. Sometimes, if not always, the head will lock into place on the right side above the ink head cleaning sponges that release ink to the lower ink pads.To correct the problem you need to clean the sponge area, I use cotton swabs. If the head is locked to need to release the carriage lock with a screwdriver. This will require removing the cover, but not necessarily the bottom of the unit.There is a 179 page service manual available for download for $16.50. There are free downloads of this manual, but usually are missing the 100 pages.You can remove the cover by:1. Remove the three screws on the rear housing (One to the left of the power plug, one on the opposite side and one in the lower middle bottom.2. Remove the three screws inside the upper housing (Just under the lid where the hinge is).3. Remove the screw under the left and right side in back below the vents.4. In the back pull the white ribbon closest to you out of the block, do not try to remove the block itself.5. Place a screwdriver into the slot both on the right and lift of the bottom corners on the back to release the hooks that hold the upper unit.6. Lastly, put a screwdriver into the notches on the bottom of the printer located in the front right and left, they are spring loaded.7. Remove cover.8. The head lock release screw is in the right side of the printer and is partially covered by the lower housing. I drilled a half inch hole into the side as to be able to insert a screwdriver. Turn the screw to the left and the head will rise out of the locked position. You only need to turn enough to release the head.9. Clean the sponges and any areas you see with excess ink.10. Place the cover on the unit enough to plug the white ribbon back in and turn the unit on.If the printer lights stop flashing then you are all set.

Read Full Q/A … :

Epson Stylus CX3200

Epson Stylus Photo R230(2 red indicator blinking)
ANSWER : 2 red indicator blinking

Read Full Q/A … :

Epson Stylus CX3200

the indicator lamp below the ink indicator sign bottom is lighting red in colour rapidly.
ANSWER : We have free Trial Reset Key.

Read Full Q/A … :

Epson Stylus CX3200