Epson M 255

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Make sure your paper meets the specifications for your product. If paper dust builds up on the rollers, they may lose traction and become unable to feed paper properly. Clean the paper guide. If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary.
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust. Select one of the following: Auto: automatically adjusts the paper feed setting (takes 9 to 35 minutes to complete); Epson recommends running this option first.
A paper feed issue can occur for several reasons, such as dusty or contaminated paper rollers, the condition of the paper in the tray, or even issues with the software.
There are a few things that could be the cause of this problem, including: Empty ink or toner cartridges that need replacing. Ink or toner cartridges that have become dislodged from their proper place. The wrong paper size loaded in the input tray.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
There are different methods of paper feeding. With dot matrix printers, paper is often feed through pins on a wheel that grab and slowly move paper through the printer. With inkjet and other page printers, paper is fed through the printer with rollers that grab and move the paper through the printer.
When Roll Auto Cut Off is selected, this button feeds the paper if pressed and held for 3 seconds. Then you can cut the paper using the manual cutter unit. When the printer is drying ink, this button stops the ink drying process and ejects the paper if pressed and held for 3 seconds.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
Paper Feed Rollers

Created with a blending technology developed based on our extensive experience, these materials offer both a high friction coefficient retaining characteristic and superb abrasion resistance. We also mass-produce belt-shaped samples, in addition to ordinary rolls.

Printer rollers are the small circular rubber pieces that help feed printer paper through your printer. Over time, they can accumulate dust from the paper and ink residue from printing double-sided pages. To clean your printer rollers, you`ll need to first locate them in your printer.
Continuous form feed and friction feed are the two types of paper feeder mechanisms. Dot matrix printers use continuous form feed, and laser printers use friction feed.
Sheet feeder: Holds the blank paper and automatically feeds the paper during printing.
The manual feed slot is located on the front of your printer. It can be closed when not in use, making the product more compact. Use the manual feed slot to print transparencies, labels, envelopes or postcards in addition to making quick runs of paper types or sizes that are not currently loaded in the paper tray.
Insert the paper with the printable side up. Place the paper against the left side of the manual feed slot and insert it horizontally. Load one sheet at a time. Open the printer cover and adjust the end of the paper so that it is 1 cm from the roller.
“Manual Feed” is an indication that your machine`s Tray Setting or the paper source in the printer driver has been set to Manual Feed, but there`s no paper loaded in the manual feed slot.
Centralized automated feed systems feature a central feed silo(s), with blowers and hoses to distribute feed to the different tanks. Large amounts of feed can be loaded into the silos, reducing the amount of labour needed to load feeders.
This issue is typically caused when the Auto Crop feature is enabled within the scan settings. This feature can only be used from the Flatbed, so the machine`s scan function will bypass the ADF by default.
An ADF (Automatic Document Feeder) is a great feature to have when used properly. It gives you the ability to feed several pages into a multifunction printer, scanner or copier, allowing you print print, copy or scan multiple pages at once without having to manually insert each piece of paper.
Document feeder

Press the Power button ( ) to turn off the product. Disconnect the power cord. Open the document feeder cover. Lift the side lever to open the pickup assembly, and then gently pull the jammed paper out.

To remove dust or smudges, gently wipe the obstacle sensor glass with lens-cleaning paper. To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the obstacle sensor glass. Warning: Do not use a lens cleaner that contains flammable gas.
Capacitive sensors can detect objects that have a dielectric constant that is different from air. Hence, these sensors can detect objects made from a wide variety of materials such as plastic, paper, wood, etc.
CANON PIXMA MG2522 NOT FEEDING PAPER

Check whether the paper is loaded properly into the paper tray. If not, remove and reload them properly. Make sure that you have loaded the recommended paper type. Also, ensure that the paper is not overloaded in the tray of your Canon printer.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

Epson M 255

Epson 2200 stuck in start up loop
ANSWER : I fixed it, unplug it , push the on button and I let it sit over night and then plug it in.

Read Full Q/A … :

Epson M 255

HP 2200 – Won't feed paper and squeals
ANSWER : My suggestion: laser mirror motor has dry bearing (the squeal) and the printer won’t feed paper until it gets up to speed. Someplace on fixyourownprinter is an article explaining how to get to the motor & put a drop of TriFlow Synthetic PTFE oil on it. Worked for me…

Read Full Q/A … :

Epson M 255

Epson 2200 – factory rep, can you help me?
ANSWER : You can feed the paper through the manual feed slot in the back. Read this and try it. http://www.steves-digicams.com/2002_reviews/epson_2200.html

Read Full Q/A … :

Epson M 255

Paper feeds straight through without printing on an Epson R2400
ANSWER : I was able to get it to print the internal test page by holding down the sheet paper feed button while turning the machine on — then continuing to hold the sheet paper feed button. It took several attempts, feeding a page straight through, but eventually it caught the sheet and printed. So it may be a timing issue as others have mentioned. It could still mean that the feed rollers are worn out. The back side of the large D-shaped feed roller has visible abrasion on it. The abrasion is difficult to see as the roller does not stay with the flat side exposed.

Read Full Q/A … :

Epson M 255

Lexmark paper feed problems
ANSWER : On my X204n Lexmark laser printer, it was doing the same thing you described – basically sounded like it was trying to pick up the paper from the tray and then failing after several seconds. When you’d open the paper tray, the paper looked like it had been partially taken up with some black scuff marks on the paper that lined up with the rollers that take up the paper. I inspected the rollers and although they looked a bit smooth and worn, didn’t seem like they should be a problem. However, this particular model has just a rubber tire almost like a car tire – the rubber can come off the hard plastic wheel on the inner portion. So I popped off the two rubber “tires”, turned them inside out and put them back on. When turned inside out, the rubber looked nice and … rubbery and had a lot more grippy feeling to them. The very first printing attempt after that and the paper sucked up perfectly with no problems. I think the problem is solved! So if you have similar “tires” that take up the paper, try flipping them and see if it works for you too.

Read Full Q/A … :

Epson M 255

EPSON Stylus NX400 Vista Print Problem
ANSWER : I have the similar issue. The browse button would not open the connection listing the shared printer. How can I fix it? Please respond to this post or contact me via buy essays. Thank you in advance!

Read Full Q/A … :

Epson M 255

HP DeskJet 722C Paper Feed Problem
ANSWER : Detach the force string from the holding nothing back one and expel all paper from it.

Read Full Q/A … :

Epson M 255