Brother MFC J270W

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

With a blank document open in Word, select the Mailings tab and pick Envelopes on the left. In the window that appears, enter the delivery address details at the top and return address beneath. Select Options to choose the envelope size and printing options.
Most printers will allow you to print directly onto an envelope. This is especially useful if you have a lot of letters to send, for example.
So, when you load envelopes in your printer and hit `print` without setting a custom paper size, it thinks you`re still using US Letter (or A4) printer paper. And that causes all sorts of alignment problems. Go into your settings and type in the exact measurements of your envelopes in the Printer Paper Size field.
Envelope and Address Printing Machines. Directly printing names and addresses onto envelopes is an easy way to personalise your mail without applying labels. Envelope and address printers can also apply marketing images for impactful mail.
Q11-Which command lets you print envelopes from Writer? Ans- By using Insert menu- Envelope, we can print envelopes from Writer.
You`ll put the sender`s name and return address on the top left corner and the recipient`s name and mailing address in the lower center. And you`ll typically place a stamp on it in the top right corner. All these generally go on the same flat side of the envelope.
First, ensure that you are using paper that meets Brother recommended paper specifications. Click here to see what kind of paper you can use. The printer can load envelopes from the multi-purpose tray. Your application software must be set up to print on the envelope size you are using.
I`ve found that placing the envelopes upside down in the printer feed works best for the correct alignment, with the side you will print on facing you. However, your printer may be different than mine so again it`s important to run a few test prints until you get the settings just right.
Q11-Which command lets you print envelopes from Writer? Ans- By using Insert menu- Envelope, we can print envelopes from Writer.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

Brother MFC J270W

when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?

Read Full Q/A … :

Brother MFC J270W

Print file sent but no printing occurs
ANSWER : Been working on these since they first were released. Never seen a problem like yours. If it happens again, try doing an engine test, as it bypasses the formatter board. The engine test is located at the right side of the manual tray opening. Look for a hole in the side wall. Stick something like a paper clip into it to actuate the test button. It will then print a lined test page. If it does that, then it points to the formatter board as the cause of your problem.

Read Full Q/A … :

Brother MFC J270W

Prints blank pages, won't print from computer
ANSWER : Don’t know why you replaced the fuser, but assuming you had print before, then it must have been something you did during the procedure. Only thing I can suggest is to recheck your work. Just because you reinstalled a connector doesn’t mean that it is seated firmly enough to work. Any flat ribbon connectors that you removed and reinstalled, check to see that the contacts are all flat and not peeled back.

Read Full Q/A … :

Brother MFC J270W

Envelop Printing Faded
ANSWER : Fuser can’t cause the problem. I’ve seen a lot of people break the transfer roller mounts when installing them improperly. If the transfer roller isn’t being pushed up against the back of the paper, then the toner won’t pull down to the front of the paper off of the toner cartridge. Push down on each end and it should spring back up.

Read Full Q/A … :

Brother MFC J270W

Paper feeds straight through without printing on an Epson R2400
ANSWER : I was able to get it to print the internal test page by holding down the sheet paper feed button while turning the machine on — then continuing to hold the sheet paper feed button. It took several attempts, feeding a page straight through, but eventually it caught the sheet and printed. So it may be a timing issue as others have mentioned. It could still mean that the feed rollers are worn out. The back side of the large D-shaped feed roller has visible abrasion on it. The abrasion is difficult to see as the roller does not stay with the flat side exposed.

Read Full Q/A … :

Brother MFC J270W

Epson Artisan 835 print head cleaning question
ANSWER : I had the same problem. After reading the comments, I tried Liquid Wrench spray. 1st try got about sixty percent improvement. Tried again this time I let it set for about 10 min then did a head cleaning. Completely solved the problem. I am a little concerned about its use on plastic. So far so good.

Read Full Q/A … :

Brother MFC J270W

My printing come out blurred
ANSWER : doris…There are usually 2 reasons for blurry output on this printer. First, make sure that the alignment is correct. You can get to it from the maintenance tab on the software that came with the printer. The other common cause of blurring is debris under the printhead. Hope this helps.

Read Full Q/A … :

Brother MFC J270W