Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

The drum unit is an electrically charged cylinder that fuses that toner powder onto paper to create text and images. Both of these components are essential for producing a print.
The drum uses static electricity to attract powdered toner to the drums cylinder. The drum rolls the toner onto the paper in the form of your print. The toner is melted & pressed onto the paper by heat from a fuser as it passes through its rollers. Your print comes out of the printer.
If your drum is not recognizing in the printer, there may be an issue with the gold chip on the end of the toner cartridge. This chip communicates with the printer to create a print and if it is not reading properly, the toner / drum unit will not work. Sometimes fingerprint oil or dust can cause this error.
The message `Replace Drum` will appear if the drum unit is at the end of its rated life. Brother recommends that customers use only genuine Brother drum units and/or toner cartridges.
Use an activated toner cloth, stretched tautly, and carefully wipe down the drum exterior to remove loose toner. Then use a cotton ball saturated with 99% pure isopropyl (rubbing) alcohol. Clean any patches of stubborn toner still attached to the drum. Use toner cloth or lint-free microfiber to clean the print rollers.
You should replace it when your image quality declines and does not improve even after changing your toner. Or simply replace your drum when your printer notifies you to do so. When the replace drum light or message comes on, your printer might stop working without much notice.
Laser printers use a single drum, but may have more than one toner cartridge. Monochrome models use only black toner, and color laser printers have four cartridges: black, cyan, magenta and yellow. When used in combination, the printer produces all colors, hues and shades of gray.
An imaging drum is an essential part in the operation of your modern laser printer. Along with the toner and roller, the imaging drum helps finalize the ink-to-paper process, receiving the image or text and then transferring it to paper.
There are many factors that determine the actual drum life, such as the temperature, humidity, type of paper, type of toner used, number of pages per print job and so on. Under ideal conditions, the average drum life is estimated at approximately 12,000 pages.
You can refresh the drum to improve print quality if streaks or white spots appear on printed images. Consult your service representative before using this function. Do no printing operations while the drum is being refreshed.
Carefully wipe off any dirty areas visible on the drum. If the drum unit is dirty, apply some rubbing alcohol onto your lint-free cloth and carefully wipe the body of the drum unit.
Water will often get the job done and it has the least risk factor involved when it comes to cleaning your drums. Using a damp cloth to wipe down your kit will get the job done most of the time. If you want to do some heavier cleaning, you can use dish soap.
The drum unit may need replacing if you notice the printer producing blurry, low-quality images. Black or colored toner spots on printouts also indicates a failing drum unit. In some cases, horizontal lines may develop across the printout every time the paper passes the failing part of the drum.
To avoid print quality problems, DO NOT touch the surface of the drum unit, only the wheel on the end.
You don`t need a drum machine, but it`s unlikely you`ll regret buying one if you do; having pads to bash out rhythms rather than simply drawing them into a window on your software of choice will make production a lot more fun.
1. On the printer display home screen, select the “set up” button (it looks like a gear). 2. Select “settings” > “device settings” > “reset settings” > “reset all” > “OK” and then “Yes.”
Reset. Resetting the printer stops printing and clears the current print job received from the active interface. You may want to reset the printer when there is a problem with the print job itself and the printer cannot print successfully.
In the Command Prompt type, net stop spooler, then press Enter to Stop the Print Spooler. In the Command Prompt type, net start spooler, then press Enter to Start the Print Spooler.
The username is admin and cannot be changed. The factory default password is password and can be changed using the Dell Printer Configuration Web Tool, Set Password link.
What is a default printer? A default printer is the printer, which all print jobs are sent to unless otherwise is specified – in other words: your primary printer. The installation of a default printer prevents Lasernet from asking the user what printer they want to use each time they print a business document.
Standard drums have inside dimensions of 572 millimetres (22.5 in) diameter and 851 millimetres (33.5 in) height. These dimensions yield a volume of about 218.7 litres (57.8 US gal; 48.1 imp gal), but they are commonly filled to about 200 litres.
All laser printers require a toner cartridge and a drum unit to produce a print. However, some printers only need you to replace the toner cartridge, and others require that you regularly replace both the toner cartridge and the drum unit. Most printers use toner cartridges with the drum unit built into the cartridge.
Printer is an output device, which is used to print information on paper.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Dell 3100cn drum cartridge replacement
ANSWER : I have the same problem with excess toner causing lines over the printed page. Have tried to find where the excess toner is stored but cannot do so. No green arrows; there are blue errors but there are no screws beneath these. Have tried removing adjacent screws, but this did not help. Does anyone have a picture of the actual site where the screws need to be removed; for the Dell 3010cn drum cartridge? Bernie

Read Full Q/A … :
Unknown Printer

Dell Laser MFP 1600n constant paper jam
ANSWER : I’m having a similar issue, checked you resolution and found the little grey piece seems to be in place and able to rock back and forth. When I send a job to the printer it sounds like it is trying to pick up the paper then I get the ‘Jam 0’ error. Any ideas ?

Read Full Q/A … :
Unknown Printer

dell 1700 with paper jams
ANSWER : clutch doesn’t lower the roller assembly. The little bum on the paper tray will push the roller assembly down when you push the paper tray inside the unit. Clutch is only involving in rotating the rollers.

Read Full Q/A … :
Unknown Printer

diagonal stripe pattern
ANSWER : I done and solved this issue dude!!!you can contact me i`ll text you by sms.

Read Full Q/A … :
Unknown Printer

Print Quality Issue (Streaks and Ghosting)
ANSWER : Streaks are mostly caused by internal drum wiper blades that clean left over toner off the drum to prepare it for a new image. Ghosting is caused by a leftover image on the drum. The 6 inches that you mention would be the circumference of the part that is causing it. Fusers will never cause either problem.

Read Full Q/A … :
Unknown Printer

image drum message
ANSWER : You don’t have to replace it until it wears enough to affect the print quality. You’ll get spots or stripes. Here you go on a free reset. If you read the thread, someone says the procedure also works on your model. http://www.fixyourownprinter.com/posts/33634

Read Full Q/A … :
Unknown Printer

toner cartrigdes and drums
ANSWER : You can, but there are good knock-offs and bad ones. I’ve run into ones that come totally empty. Ones that don’t have the chips installed that identify themselves to the printer. Ones that have sat on a shelf for years and fail on installation. I could go on, but I’m sure you get the idea. I use http://directpreciseimaging.com/ Mostly because I set him up in business and he’s local to me. I have very few problems with his products.

Read Full Q/A … :
Unknown Printer

RESET OKIDATA TONER DRUM
ANSWER : HI there, oki image drums contain a fuse. You can reset them if they are working/printing ok by replacing the fuse. Hope this helps. The fuse is located inside the unit so is a bit fiddly.

Read Full Q/A … :
Unknown Printer