Epson Stylus CX5200
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Reasons for Epson printer will not print from computer
Not properly connected to the electrical supply. Not set as a default printer. Low ink levels. Jammed paper.
Make sure the USB cable is connected securely at both ends and meets the requirements. Run a printer check. If the test page prints, make sure your software is installed correctly. Make sure the printer cover is closed.
The Cause of Clogs
Printheads clog because nozzles get blocked by either air or ink. Clogs usually happen when: You keep printing with depleted ink cartridges. Using empty ink cartridges can result in air bubbles that can clog your cartridge and/or printhead.
If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.
Several factors may cause the product to print blank pages, such as print settings, low ink, or the product itself. Check the following: Make sure the product is placed on a flat, stable surface that extends beyond the base in all directions. The product won`t operate properly if it`s tilted or at an angle.
Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.
Yes, you can reset the print settings to their original, default values. Press and hold down the Cancel button for 3 seconds. When the message to reset the printer to default settings appears, press OK to reset the print settings.
There are numerous possible causes for a printer that`s randomly producing blanks. The most common ones are empty ink cartridges, improper cartridge installation, and congested nozzles. Driver and software issues can sometimes cause this problem as well. Running out of ink?
If you have problems feeding paper, try these solutions: If paper does not feed for printing, remove it from the rear feed slot or cassette. Reload it, then adjust the edge guides. Make sure the paper stack is not above the tab on the edge guides inside the cassette or rear feed slot.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.
Read Full Q/A … :
Epson Stylus CX5200
when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?
Read Full Q/A … :
Epson Stylus CX5200
Print file sent but no printing occurs
ANSWER : Been working on these since they first were released. Never seen a problem like yours. If it happens again, try doing an engine test, as it bypasses the formatter board. The engine test is located at the right side of the manual tray opening. Look for a hole in the side wall. Stick something like a paper clip into it to actuate the test button. It will then print a lined test page. If it does that, then it points to the formatter board as the cause of your problem.
Read Full Q/A … :
Epson Stylus CX5200
Prints blank pages, won't print from computer
ANSWER : Don’t know why you replaced the fuser, but assuming you had print before, then it must have been something you did during the procedure. Only thing I can suggest is to recheck your work. Just because you reinstalled a connector doesn’t mean that it is seated firmly enough to work. Any flat ribbon connectors that you removed and reinstalled, check to see that the contacts are all flat and not peeled back.
Read Full Q/A … :
Epson Stylus CX5200
Epson Artisan 835 print head cleaning question
ANSWER : I had the same problem. After reading the comments, I tried Liquid Wrench spray. 1st try got about sixty percent improvement. Tried again this time I let it set for about 10 min then did a head cleaning. Completely solved the problem. I am a little concerned about its use on plastic. So far so good.
Read Full Q/A … :
Epson Stylus CX5200
Scanning to Word
ANSWER : I find another free online ocr , supports 40+ languages, can convert image to plain txt file and searchable pdf document.
Read Full Q/A … :
Epson Stylus CX5200
My printing come out blurred
ANSWER : doris…There are usually 2 reasons for blurry output on this printer. First, make sure that the alignment is correct. You can get to it from the maintenance tab on the software that came with the printer. The other common cause of blurring is debris under the printhead. Hope this helps.
Read Full Q/A … :
Epson Stylus CX5200
problems with printing
ANSWER : Check your settings to make sure they are Left to Right print order. If they are then reinstall printer driver. If that doesn’t correct problem uninstall printer, reboot computer, and reinstall printer.
Read Full Q/A … :
Epson Stylus CX5200