Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If the paper is even slightly askew, the rollers will pick it up a little crooked, and — guess what — the crooked sheet will immediately get jammed. So even though there`s no paper stuck when you start printing, the loose paper guides are ensuring that a sheet gets jammed whenever the printer starts doing its thing.
your pickup roller is dirty and the printer can`t grab a piece of paper. it will say paper jam when it does this. get a drop of dishsoap and clean the pickup roller of your printer with this. scrape at it with your fingernail to get the roller clean and wipe it off with a damp washcloth.
Small fragments of sticky label material commonly get torn off and stuck within your printer, collecting dust and causing a jam. Shut the printer off, get a flashlight, and try to see inside. Make sure no label fragments have jammed up your printer before proceeding.
Sometimes a paper jam error persists even though there is no jammed paper (false paper jam). Reset the printer, which might clear a false paper jam error, and then try to print again. With the printer turned on, disconnect the power cord from the printer. Unplug the power cord from the power source.
If your printer has a paper path cover behind the carriage, remove the cover, and then remove any jammed paper. Pull out the input tray, and then remove any jammed paper. If your printer has a bottom cleanout door, carefully lift the printer and look under it, and then remove any jammed paper from the bottom cleanout.
If your printer has a paper path cover behind the carriage, remove the cover, and then remove any jammed paper. Pull out the input tray, and then remove any jammed paper. If your printer has a bottom cleanout door, carefully lift the printer and look under it, and then remove any jammed paper from the bottom cleanout.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :
Unknown Printer

Paper Jam error but no paper jam
ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.

Read Full Q/A … :
Unknown Printer

Canon mx410 Paper jam message, but no paper jam?!
ANSWER : I have exactly the same problem, no answers 😳

Read Full Q/A … :
Unknown Printer

Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :
Unknown Printer

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :
Unknown Printer

Paper jam in tray 2 (but no paper pulled from tray) also M476DN models
ANSWER : Isopropyl alcohol is not recommended for rubber rollers. It dries out the rubber and hasten it’s cracking and breaking. It will do nothing to restore the grip. Those rollers are really hard to replace. It would be easy if that dumbass secondary menu really worked. None of the techs I’ve spoke to ever got into it. Everyone I know sends a print job and listens for the roller to rotate into position where you can pull it off.

Read Full Q/A … :
Unknown Printer

Keep getting a paper jam message. There is no jam.
ANSWER : You can quit wondering. Parts are unavailable. I’ve seen posts where people have 3D printed the parts or machined them out of metal.

Read Full Q/A … :
Unknown Printer

message error: ADF paper jam
ANSWER : There is a thin plastic arm that the paper pushes on. It is spring loaded. If it doesn’t return and unblock the sensor after the paper passes it, you get the paper jam warning. I’m guessing that is the spring you are referring to.

Read Full Q/A … :
Unknown Printer