Canon Pixma IP6000

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Restart your computer – this often will recover any lost connections with wireless devices. Power off and on the printer, and even the access point or wireless router your printer connects to. Check your printer configuration – you may not be assigned to the correct port for the printer.
Check that all printer cables are connected properly and be sure that the printer is turned on. If everything is connected properly and powered up, go to the computer`s “control panel” from the “start” menu. Choose “printers” and be sure that your printer is selected as the default.
With the printer powered on, select Setup . Select Device settings . Scroll to the bottom of the menu list and select Reset settings. In the Reset settings menu, select the desired area you want to set back to the factory defaults.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
A component found in electrostatic printers, laser printers, and xerographic printers and photocopiers. The fuser unit is used to permanently bond toner to a substrate by applying heat and pressure. A fuser unit is made up of two rollers; one to apply heat and one to apply pressure.
Hold the on/off button and press the stop button 5 times. Release the on/off button. The printer resets itself and restarts automatically afterwards.
Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.
If there is plenty of ink and the printer does not print, clean the Print Head then print the nozzle check pattern to ensure ink is ejected properly. If the problem is not resolved after performing Print Head Cleaning twice, carry out the Print Head Deep Cleaning.
If the paper feed rollers are dirty or have paper dust on them, the paper may not be fed properly. When this happens, you`ll need to clean the rollers twice: once with paper loaded, and once without.
If the paper feed rollers are dirty or have paper dust on them, the paper may not be fed properly. When this happens, you`ll need to clean the rollers twice: once with paper loaded, and once without.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

replacing waste ink absorber on Canon Pixma ip6000
ANSWER : ditto, ditto & ditto

Read Full Q/A … :

Canon Pixma IP6000

Canon Pixma MP610 won't print in black
ANSWER : Printer cleanings use wet ink to clear dried up ink. Yeah, that works real well. The best way to clean the heads is remove all the ink tanks. Next to the tanks on the right, there is a plastic release lever. Pull up on it and it will release the heads. Reach in and pull them out. Take the heads over to the sink and run hot tap water into the screen for the black and then turn it over and run it over the heads on the bottom. Repeat a few times and reinstall.

Read Full Q/A … :

Canon Pixma IP6000

Canon Pixma iP8720 Ink Compartment Stuck
ANSWER : Here are some solutions you can try. http://fix-your-printer.blogspot.com/2013/01/how-to-fix-error-6a81-on-canon-printers.html

Read Full Q/A … :

Canon Pixma IP6000

Full Ink Tank in Canon Pixma ip4000
ANSWER : It had been exactly the same subject, could not find an appropriate broker and process for earnings finally had to rummage through the Web, and there I came across this page http://optioninvest.org .Possibly you’ll find there is a therapy to your condition, thanks for the fascination!))

Read Full Q/A … :

Canon Pixma IP6000

Canon PIXMA MP190 – paper pulls to one side and ja
ANSWER : My Canon MP470 pulled paper to one side. Thanks for the simple solution. It worked and made doing my taxes a little less of a pain.

Read Full Q/A … :

Canon Pixma IP6000

Canon pixma – ink absorber almost full
ANSWER : They are on the bottom of the printer. If you want to clean them, you can take them out and wash them in hot tap water. Wring them out like a sponge. You will need to reset the printer. http://jezpinions.blogspot.com/2012/03/canon-mg6150-ink-absorber-reset-error.html

Read Full Q/A … :

Canon Pixma IP6000

Canon Pixma MX882 won't print black text
ANSWER : Yeah I’m having the same problem with my Canon MX882. I’ve refilled the pigment tank, cleaned the print head and I still get no pigment black at all. I think it has something to do with the purge unit, but I don’t see any instructions on how to clean it. If I can figure it out, I’ll let you know.

Read Full Q/A … :

Canon Pixma IP6000

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :

Canon Pixma IP6000