Canon Bubblejet (BJ) 5
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Five flashes:Print Head is not installed/Print Head is defective. Follow the directions given in your setup manual to install the Print Head. If the Print Head is already installed, remove the Print Head once and then reinstall it. If the error is still not resolved, the Print Head may be damaged.
Lights or flashes orange when an error occurs, such as paper-out or ink-out.
When an error occurs in printing such as the machine is out of paper or paper is jammed, a troubleshooting message is displayed automatically. Take the appropriate action described in the message. When an error occurs, the Alarm lamp flashes orange and a Support Code (error number) is displayed on the computer screen.
The ink has run out. Replace the ink cartridge and close the paper output cover. If printing is in progress and you want to continue printing, press the printer`s Stop/Reset button for at least 5 seconds with the ink cartridge installed. Then printing can continue under the ink out condition.
Error code E05
This error code may cause an orange light on your machine to blink 5 times and is caused by the print head not being installed at all or it may have been installed incorrectly.
Ink has run out. (The lamp on the ink tank flashes.) If printing is in progress, stop printing, replace the ink tank, and then print again. Printing under the current condition may damage the printer.
Canon MG3550 – Error Codes
Three flashes – Paper jam. Four flashes – The cartridge is not installed properly. Five flashes – The cartridge is not installed properly. Seven flashes – The cartridge is not installed in the correct position.
Ten flashes: The Front Tray is not set to its correct position./The Front Tray was moved during printing. When printing from the Rear Tray, return the Front Tray to its normal printing position, make sure that paper is loaded in the Rear Tray, then press the RESUME/CANCEL button on the printer to resume printing.
The printer is offline.
With the printer powered on, select Setup . Select Device settings . Scroll to the bottom of the menu list and select Reset settings.
The orange plastic piece holds the ink carriage in place when the printer is first boxed up. That piece is designed to be removed from the printer when the printer is set up for the first time. The orange plastic piece can be thrown away.
The yellow triangle on the printer is the alarm lamp of the printer; if it is lit, it indicates that there is an item that needs to be addressed on the printer.
Error Code 5 is a Windows error code that appears when the user does not have sufficient permission to access the requested file or location.
This error can sometimes occur even when you`re not trying to print, or if you don`t have a printer installed. To overcome this issue, the first thing to check is to make sure you have the latest printer driver installed for your printer.
The power supply unit needs to be replaced.
You need to replace the power supply unit if the light is still off or flashing orange.
Usually, it should not take more than a few minutes to restore the printer to its factory settings. However, I recommend you to perform the following steps to isolate the issue and arrive at a fix: Disconnect the power cable from the printer while the printer is still ON.
Press the Setup button, press the + button until “13” appears on the LCD, and then press the Black button or the Color button. The network settings are initialized.
When those lights are lit, that is an indication that the ink cartridges would need to be replaced.
– Alarm lamp flashes orange: An error has occurred and the machine is not ready to print. – ON lamp flashes green and Alarm lamp flashes orange alternately: An error that requires contacting the service center may have occurred. Lights or flashes orange when an error occurs, such as paper-out or ink-out.
Four flashes: The ink tank is not installed./Ink tank is not installed properly./Ink may have run out. The ink tank is not installed. Install the ink tank.
If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.
ON lamp flashes: The printer is getting ready to print, or printing is in progress. Alarm lamp flashes: An error has occurred and the printer is not ready to print. ON lamp flashes and Alarm lamp flashes alternately: An error that requires contacting the service center may have occurred.
This vibrant hue symbolizes adventure, ambition, creativity, and sociability. Orange is often associated with positivity.
The hex code for orange is #FFA500.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
ip3000 pixma fried with 240 volts
ANSWER : You will probably need a power supply and possibly a control board (unless it survived). There may be more than that which fried as well…without doing an electrical diagnostics it’s hard to say.
Read Full Q/A … :
Canon Bubblejet (BJ) 5
Pixma iP3000, Clogged Cyan print head?
ANSWER : I have had similar problem with an IP3600, but only since upgrading OS from WindowsXP to Windows7 a few weeks back, and only with the PG fat Black ink.
Read Full Q/A … :
Canon Bubblejet (BJ) 5
Canon Pixma MX882 won't print black text
ANSWER : Yeah I’m having the same problem with my Canon MX882. I’ve refilled the pigment tank, cleaned the print head and I still get no pigment black at all. I think it has something to do with the purge unit, but I don’t see any instructions on how to clean it. If I can figure it out, I’ll let you know.
Read Full Q/A … :
Canon Bubblejet (BJ) 5
Canon Pixma iP3000 "Open door" Error code.
ANSWER : Look for a protruding plastic on the top that goes into an indentation. Mine was in the front left side. Put a piece of cardboard into the indentation.and close the door. The top plastic piece is not pushing the door close sensor down and because its too short and the cardboard allows the sensor to be reached and pushed.
Read Full Q/A … :
Canon Bubblejet (BJ) 5
Full Ink Tank in Canon Pixma ip4000
ANSWER : It had been exactly the same subject, could not find an appropriate broker and process for earnings finally had to rummage through the Web, and there I came across this page http://optioninvest.org .Possibly you’ll find there is a therapy to your condition, thanks for the fascination!))
Read Full Q/A … :
Canon Bubblejet (BJ) 5
Canon Pixma MP610 won't print in black
ANSWER : Printer cleanings use wet ink to clear dried up ink. Yeah, that works real well. The best way to clean the heads is remove all the ink tanks. Next to the tanks on the right, there is a plastic release lever. Pull up on it and it will release the heads. Reach in and pull them out. Take the heads over to the sink and run hot tap water into the screen for the black and then turn it over and run it over the heads on the bottom. Repeat a few times and reinstall.
Read Full Q/A … :
Canon Bubblejet (BJ) 5
5 orange blinks – what do I do?
ANSWER : http://www.justanswer.com/printers/4mvy4-canon-pixma-ip5200-orange-alarm-light-flashing.html
Read Full Q/A … :
Canon Bubblejet (BJ) 5
Canon Pixma iP8720 Ink Compartment Stuck
ANSWER : Here are some solutions you can try. http://fix-your-printer.blogspot.com/2013/01/how-to-fix-error-6a81-on-canon-printers.html
Read Full Q/A … :
Canon Bubblejet (BJ) 5