Canon Bubblejet (BJ) 5

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Error code E05

This error code may cause an orange light on your machine to blink 5 times and is caused by the print head not being installed at all or it may have been installed incorrectly.

There is no paper in the rear tray. Paper is not loaded in the rear tray properly.
Restart your computer – this often will recover any lost connections with wireless devices. Power off and on the printer, and even the access point or wireless router your printer connects to. Check your printer configuration – you may not be assigned to the correct port for the printer.
Five flashes:Print Head is not installed/Print Head is defective. Follow the directions given in your setup manual to install the Print Head. If the Print Head is already installed, remove the Print Head once and then reinstall it. If the error is still not resolved, the Print Head may be damaged.
This error can sometimes occur even when you`re not trying to print, or if you don`t have a printer installed. To overcome this issue, the first thing to check is to make sure you have the latest printer driver installed for your printer.
The main cause of the issue is the absence of the printer driver software. Driver software that are incompatible with the system and also software that lack updates are other reasons that cause the printer error 5 to occur. Also, driver software for a particular device should be configured after its installation.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Canon printers produce error codes for one of several reasons: The settings for your printer might not be compatible with the document you`re trying to print. The loading bay for your paper might have become lodged with paper or you`re using the wrong type of paper.
Unplug and restart your printer

Sometimes power cycling your printer can resolve the issue. Turn off your printer and unplug it, wait 30 seconds, plug your printer back in, and then turn the printer back on. If your printer still doesn`t work, continue to step 2.

The red flashing light on your camera shows that the camera is accessing the memory card. It`s normal to see a red light when the camera takes a photo.
ON lamp flashes: The printer is getting ready to print, or printing is in progress. Alarm lamp flashes: An error has occurred and the printer is not ready to print. ON lamp flashes and Alarm lamp flashes alternately: An error that requires contacting the service center may have occurred.
Error Code 5 is a Windows error code that appears when the user does not have sufficient permission to access the requested file or location.
Some services may conflict with some applications; as a result, event ID 1000 appears. To fix this issue, you can perform a Clean Boot. Input msconfig to the Run dialog box and press Enter. Click Selective Startup and uncheck Load startup items.
This means that the credentials entered by you are wrong.
This error is most commonly caused by one or more DNS records in the Cloudflare dashboard pointing to a Cloudflare IP address. It can also be caused if your DNS record(s) reference another reverse proxy. To resolve this, you should edit your DNS records to point to your origin server`s IP address.
E, 0, 8 E08 Ink absorber is almost full. The ink absorber collects excess ink after head cleaning or during printing. Ink usually goes into a bottle which eventually becomes full. There is a risk that ink can begin to spill.
a misprint or misspelling in a text.
Open Settings -> Devices -> Printers and Scanners (or run a quick access URI command: ms-settings:printers ); Select a printer you want to remove and click Remove Device; Confirm the printer removal.
Printer is out of paper. Printing one side is complete if you are performing manual duplex printing. If the printer is out of paper: 1000.
The Canon 5200 error is often related to the ink levels present in printer cartridges. Turning your printer off and on again can reset the printer`s mechanism for reading ink levels and get you back to printing in no time.
A `Paper has Jammed` message and light blinks

Remove any ejected paper from the front or back of the printer. Open the paper tray cover. Remove any loose photo paper from the paper tray, and then check for and remove any bent, wrinkled, or torn paper.

When a printer error occurs, the light on the front of your printer flashes orange as shown below. Five flashes means the print head is not installed or is defective. The light flashes (A), then goes off (B) (this repeats 5 times).
Yes, if the computer is sleep or standby mode it is normal for the power light LED to flash, or blink. This lets you know the computer is still on, and that it`s in a power-saving mode. If your computer is in this mode, press any keyboard key or button on a mouse to exit power saving mode.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Print problem with Canon MP620
ANSWER : Open the front of the printer.

Read Full Q/A … :

Canon Bubblejet (BJ) 5

Canon pixma – ink absorber almost full
ANSWER : They are on the bottom of the printer. If you want to clean them, you can take them out and wash them in hot tap water. Wring them out like a sponge. You will need to reset the printer. http://jezpinions.blogspot.com/2012/03/canon-mg6150-ink-absorber-reset-error.html

Read Full Q/A … :

Canon Bubblejet (BJ) 5

Canon Pixma iP8720 Ink Compartment Stuck
ANSWER : Here are some solutions you can try. http://fix-your-printer.blogspot.com/2013/01/how-to-fix-error-6a81-on-canon-printers.html

Read Full Q/A … :

Canon Bubblejet (BJ) 5

Canon Pixma MX882 won't print black text
ANSWER : Yeah I’m having the same problem with my Canon MX882. I’ve refilled the pigment tank, cleaned the print head and I still get no pigment black at all. I think it has something to do with the purge unit, but I don’t see any instructions on how to clean it. If I can figure it out, I’ll let you know.

Read Full Q/A … :

Canon Bubblejet (BJ) 5

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :

Canon Bubblejet (BJ) 5

Canon PIXMA MP190 – paper pulls to one side and ja
ANSWER : My Canon MP470 pulled paper to one side. Thanks for the simple solution. It worked and made doing my taxes a little less of a pain.

Read Full Q/A … :

Canon Bubblejet (BJ) 5

Full Ink Tank in Canon Pixma ip4000
ANSWER : It had been exactly the same subject, could not find an appropriate broker and process for earnings finally had to rummage through the Web, and there I came across this page http://optioninvest.org .Possibly you’ll find there is a therapy to your condition, thanks for the fascination!))

Read Full Q/A … :

Canon Bubblejet (BJ) 5

Canon Pixma MP610 won't print in black
ANSWER : Printer cleanings use wet ink to clear dried up ink. Yeah, that works real well. The best way to clean the heads is remove all the ink tanks. Next to the tanks on the right, there is a plastic release lever. Pull up on it and it will release the heads. Reach in and pull them out. Take the heads over to the sink and run hot tap water into the screen for the black and then turn it over and run it over the heads on the bottom. Repeat a few times and reinstall.

Read Full Q/A … :

Canon Bubblejet (BJ) 5