Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If you install the wrong ink cartridge in your printer, you will likely receive an error message on your printer display that prevents you from using the printer. Printers are smart and most will be able to tell right away if the wrong cartridge is installed.
Press down on the cartridge gently for several seconds. The LED light on the chip resetter will flash several times, indicating that contact has been made with the chip. Continue holding the cartridge in place until the LED light emits a steady light.
Verify the ink cartridge(s) is inserted properly. Some cartridges snap in place, and if they are not inserted fully, the printer won`t print anything. If a lever is moved from its original position to allow for installation of ink cartridges, ensure it is returned to its original position.
Press the button on the chip-reset tool for several seconds until the LED light on the device goes off. Then, unlock the reset tool from the cartridge. Use the resetter with other cartridges and install them back into the corresponding slots in your printer. Voila!
This is because of the chips on the ink cartridge, each chip is programmed to allow inks to only work with certain printers. Therefore, you are unable to use a different number ink in your printer which is not compatible with your printer. Check your printer manual to see what numbers your printer takes.
Can you print with one or two empty ink cartridges? The quick answer is: Yes, you can (if you own a printer model that allows it) — but you shouldn`t keep printing with an empty cartridge for too long.
Verify the ink cartridge(s) is inserted properly. Some cartridges snap in place, and if they are not inserted fully, the printer won`t print anything. If a lever is moved from its original position to allow for installation of ink cartridges, ensure it is returned to its original position.
Press the button on the chip-reset tool for several seconds until the LED light on the device goes off. Then, unlock the reset tool from the cartridge. Use the resetter with other cartridges and install them back into the corresponding slots in your printer. Voila!
Press the button on the chip-reset tool for several seconds until the LED light on the device goes off. Then, unlock the reset tool from the cartridge. Use the resetter with other cartridges and install them back into the corresponding slots in your printer. Voila!

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Canon IP1200 and IP1600 Cartridge Not Recognized
ANSWER : Cara mengatasi ink cartridge cannot be recognized printer canon – Printer Canon Pixma Ip 2770 yang telah diinfus dan mengalami kendala pada saat akan menggunakannya kendalanya tersebut ditandai dengan pesan error, “INK CARTRIDGE CANNOT BE RECOGNIZED” Ini adalah trik untuk mengatasinya: Trik menangani masalah “INK CARTRIDGE CANNOT BE RECOGNIZED” Printer anda bermasalah? Blinking 5-7 x orange? Dan muncul pesan “The following ink cartridge cannot be recognized” pada monitor anda ? permasalahan bukan pada catridge nya dan tidak perlu ganti baru, berikut cara nya – Buka cover printer – Cabut cartridge (yang bermasalah) – Tutup cover printer – Matikan printer dan cabut kabel power – Tunggu beberapa saat (kira-kira 5-10 menit) – Hidupkan printer dan langsung buka cover printer – Pasang cartridge (yang tadi anda lepas) – Matikan printer dan cabut kabel power – Hidupkan kembali – Jalankan test print Jika masih bermasalah pastikan tempat catridge anda tertutup dengan benar,jika masih bermasalah juga sebenar nya permasalahan pada infus lubang catridge warna anda, untuk memastikan cobalah anda memasang catridge warna anda yang terdahulu tidak ada masalah,jika tidak ada masalah dengan dengan catridge warna terdahulu,cobalah lepas infusan pada catridge warna anda, jika ternyata bisa tanpa dipasang selang infus catridge warna, maka dipastikan tempat catridge terlalu menekan catridge warna anda.Yang anda butuhkan adalah melakukan coakan pada tempat catridge/dekat per pegas (lihat gambar yang diberi merah dibawah ini)

Read Full Q/A … :
Unknown Printer

How to reset ink cartridge Canon Pixma MG6320
ANSWER : Your post is a bit confusing. You don’t reset the chip, you pull off the old one and replace it with the one they gave you.

Read Full Q/A … :
Unknown Printer

Canon PIXMA ip4000 Cartridges
ANSWER : It had been exactly the same subject, couldn’t discover an appropriate broker and method for earnings ultimately had to rummage through the Web, and there I ran across this website http://optioninvest.org.Probably you will find there is a remedy to your trouble, many thanks for the fascination!))

Read Full Q/A … :
Unknown Printer

Canon i560 Will not print black
ANSWER : Dang, it worked for me then wentback to normal (not working) after the test page. Oh well not bad for a 10 year old bubble jet.

Read Full Q/A … :
Unknown Printer

Canon Pixma MP150 Error Code 5100
ANSWER : Make sure you check that a copy of Gustave Holst’s journey to the stars cassette isn’t stuck in there! haha. That’s what my error 5100 was all about, I was getting ready to dismantle the thing after threatening it with a water boarding.

Read Full Q/A … :
Unknown Printer

PGBK cartridge not working
ANSWER : Did you try removing the print heads and flushing them under hot tap water?

Read Full Q/A … :
Unknown Printer

Canon MP600 died
ANSWER : hey guys I found this on the net check it out maybe somebody can make something out of it cuase they omitted this part on the service manual that I attained cause I have the same problem hope this helps.

Read Full Q/A … :
Unknown Printer

Canon Pixma iP3000 "Open door" Error code.
ANSWER : Look for a protruding plastic on the top that goes into an indentation. Mine was in the front left side. Put a piece of cardboard into the indentation.and close the door. The top plastic piece is not pushing the door close sensor down and because its too short and the cardboard allows the sensor to be reached and pushed.

Read Full Q/A … :
Unknown Printer