Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If the alarm light lights and stays lit after you you turn on your printer, and doesn`t respond to any commands on the printer panel, try the following: Check to make sure there are no paper jams or other obstructions. Unplug the printer for approximately two minutes, then plug it back in.
The Status light stays yellow and on steady (not flashing) normally to indicate that there is data remaining in the printer`s memory. Press the GO button once to print the remaining data in memory.
If a problem occurs and the printer is not working properly, the (Alarm) indicator (orange) comes on and the following service calls appear in the Printer Status Window.
The alarm and event printer service allows alarms and events to be printed out on a printer that is connected to a server or client PC via a serial port.
Solution: the paper is jammed. Remove the jammed paper, replace the paper correctly in the printer, and then press the Resume / Cancel button.
A system code is a four to six-digit numbered password that is used to arm and disarm your security system as well as provide you access to perform various other functions within the system. The primary reason these codes exist is to ensure that the person using the system is meant to have access to it.
alarm noun (WARNING)

a warning of danger, usually a loud noise or flashing light: If there`s any trouble, raise/sound the alarm by pulling the emergency cord.

The basic purpose of an automatic fire alarm system is to detect a fire in its early stages, notify the building occupants that there is a fire emergency and report the emergency to first responders.
In process automation, an alarm is defined as an audible and/or visible means of indicating to the operator an equipment malfunction, process deviation, or abnormal condition requiring an operator response.
Audible Alarm

Once the UPS has detected an overload condition, it will generally emit a long and continuous beeping sound. * CyberPower UPS systems also provide some alarm functions to notify users of UPS fault, such as battery overcharge, overheat, or output shortage, as well as the battery missing issue.

– ON lamp flashes green and Alarm lamp flashes orange alternately: An error that requires contacting the service center may have occurred. Lights or flashes orange when an error occurs, such as paper-out or ink-out.
Thirteen flashes: The ink level cannot be detected. Possible Solution: Replace the ink tank and close the top cover.
We can assume that 1234 is chosen most often because it`s easy to remember.
The Master Code is the primary code for the alarm system. In addition to arming and disarming the alarm system, the Master Code provides access to a user menu.
Alarm beeping is a built-in warning that signals the power is fading, and that a new battery will be required soon. There are two options. Go ahead and put in fresh batteries all around. The beeping should stop when you`ve hit on the culprit.
Trouble – A trouble condition means there is an issue or fault with the fire alarm system. An example would be a break in an initiating device circuit. This would show up as a trouble signal on the control unit.
Here`s a simple guide: Smoke alarms alert you with three beeps in a row. Carbon monoxide alarms alert you with four beeps. A single chirp means the battery is low or the detector should be replaced.
3 Beeps and a Pause: EMERGENCY. This type of chirp means that smoke has been detected in your home. You and your family need to evacuate and call 9-1-1 once safely outside.
Home security systems are networks of integrated electronic devices working together with a central control panel to protect against burglars and other potential home intruders. A basic home security system includes: A control panel or base station with a separate keypad. Door and window sensors. Motion sensors.
In general, there are four types of alarm systems you should consider.
The purpose of a fire detection and alarm system is to detect and warn of fire at the earliest possible time so as to enable occupiers to take the required action.
A constant beep (every second or two, and never stopping) generally means the UPS is very low on battery power, and you should shut down immediately. If there`s been no power loss and it`s still beeping periodically, your UPS is letting you know that it`s failed a self-test.
If the battery fails the self-test, the Power on LED will flash and the unit will emit a constant tone. This is a WARNING that the battery may be near the end of its life, replacement is typically recommended within 2-4 weeks.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Canon MP600 died
ANSWER : hey guys I found this on the net check it out maybe somebody can make something out of it cuase they omitted this part on the service manual that I attained cause I have the same problem hope this helps.

Read Full Q/A … :
Unknown Printer

Canon MP530 – 6A00 Purge Unit?
ANSWER : I just took apart my MP530 which produces the 6A00 error, and cleand the wiping pads, rubber blades and everything I could reach from the purge unit. I also cleaned the print head. The waste ink level in the EEPROM is 66%.

Read Full Q/A … :
Unknown Printer

Canon Pixma MP150 Error Code 5100
ANSWER : Make sure you check that a copy of Gustave Holst’s journey to the stars cassette isn’t stuck in there! haha. That’s what my error 5100 was all about, I was getting ready to dismantle the thing after threatening it with a water boarding.

Read Full Q/A … :
Unknown Printer

Canon MX922 printer with B200 service code
ANSWER : Try green copy button and red triangle in a circle together while releasing the power button upon restarting printer.

Read Full Q/A … :
Unknown Printer

Canon Printer reset tool for MP100 MP400 series
ANSWER : Thanks a million for this. I have just managed to get my MP460 Ink levels reset having tried lots of other sites and failed.

Read Full Q/A … :
Unknown Printer

Canon i560 Will not print black
ANSWER : Dang, it worked for me then wentback to normal (not working) after the test page. Oh well not bad for a 10 year old bubble jet.

Read Full Q/A … :
Unknown Printer

Canon Pixma iP3000 "Open door" Error code.
ANSWER : Look for a protruding plastic on the top that goes into an indentation. Mine was in the front left side. Put a piece of cardboard into the indentation.and close the door. The top plastic piece is not pushing the door close sensor down and because its too short and the cardboard allows the sensor to be reached and pushed.

Read Full Q/A … :
Unknown Printer

Full Ink Tank in Canon Pixma ip4000
ANSWER : It had been exactly the same subject, could not find an appropriate broker and process for earnings finally had to rummage through the Web, and there I came across this page http://optioninvest.org .Possibly you’ll find there is a therapy to your condition, thanks for the fascination!))

Read Full Q/A … :
Unknown Printer