Canon FC 2

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If the nozzle check pattern shows adequate ink, but the printer doesn`t print color, clean the printhead. After that, print a nozzle check pattern. After performing printhead cleaning, perform a printhead deep cleaning. If still, the problem persists, switch off your printer and do the deep cleaning after a day.
Set the correct paper size

When the aspect ratio of the image does not match the paper size and [Borderless] is selected, part of the image will be cut off when printed. Confirm that the paper size matches the image aspect ratio before printing.

Remove stains from the inside of the printer. If the inside of the printer becomes dirty, printed paper may get dirty, so we recommend performing cleaning regularly.
The ink cartridges may be old or low on ink, and you may need to replace them. Your printed colors can never exactly match your on-screen colors. However, you can use a color management system to get as close as possible. Try using the color management options in your printer software.
Your computer monitor uses the RGB model to create colors on the screen, whereas the printer uses the CMYK model to put the colors on paper. Thus, printers cannot replicate all the colors that a monitor does. Also, it is quite challenging to convert on-screen colors to CMYK and replicate them for printing.
If the borders are still not showing when you print, adjust the margins to give more space between the borders and the edge of the page on the document. Go to Layout > Margins, and select Custom Margins. Increase the border that corresponds with the one that`s missing when you print.
It`s usually because the printhead inside your printer is clogged or dried out. Like with most printers, Canon printheads can clog due to ink or dust drying up and collecting in the nozzle.
The first step in printer calibration is to calibrate your monitor. Then, make sure you use the correct printer driver for your printer. Within the printer driver are controls for fine-tuning the overall appearance of color from your printer. Depending on your needs, this may be sufficient to get the color you want.
Both RGB and CMYK are modes for mixing colour in graphic design. Monitors use RGB whereas printers use CMYK. This means that RGB colour mode is best for digital designs, while CMYK is best for print materials.
Text inserted in the top margin of each page of a document is called a header, and text inserted in the bottom margin is called a footer.
Footer – a section of information that appears at the bottom margin of each page of a document.
Partial prints are a common issue with printers and there are several main reasons it can occur: Problem with the print spooler (on Windows PCs) Overload of the GPU on later model Macs. Dodgy USB cord.
Ink absorber absorbs the ink used when Cleaning is executed. In order to maintain the best printing, the ink used when Cleaning is absorbed into the ink absorber inside the printer. The ink absorber requires the replacement when it is full. However, it cannot be replaced by yourself.
Why is my printer printing yellow not red? It is most likely that your image is yellow where you were expecting it to be red and you may also notice that blue parts of the image appear turquoise instead. Both of these effects are caused by a lack of magenta ink/toner on your prints.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Canon PIXMA MP 210
ANSWER : Mine was grabbing the paper from the right side only (where the roller is), sucking the paper in partway and then going sideways and jamming. I cleaned off the roller to no avail. Then I picked the printer up and looked in the paper slot and found a small screwdriver lying sideways so deep you almost couldn’t see it. I got that out and now it works fine!

Read Full Q/A … :

Canon FC 2

HP Color Laserjet 3800 problem when printing color
ANSWER : Do a cold reset

Read Full Q/A … :

Canon FC 2

HP Color Laserjet blank pages – only jetdirect page
ANSWER : What about the engine test? To do that, drop down the front tray. Feel around on the left side at the top and you’ll feel a little plastic dongle. If you lift up on that it will initiate an engine test page. That will be a page containing lines of each color.

Read Full Q/A … :

Canon FC 2

canon MX700 6A80 error, head locked
ANSWER : I bought a canon pixma 7240 but on my first use I turn it on and the power lamp and error lamp blink alternatively the print head is stuck not moving please help I can’t even put the cartridges. My email [email protected] phone number 0719013770.

Read Full Q/A … :

Canon FC 2

Canon i560 Will not print black
ANSWER : Dang, it worked for me then wentback to normal (not working) after the test page. Oh well not bad for a 10 year old bubble jet.

Read Full Q/A … :

Canon FC 2

Print problem with Canon MP620
ANSWER : Open the front of the printer.

Read Full Q/A … :

Canon FC 2

Canon Pixma Mp 230
ANSWER : Hello Hamid:

Read Full Q/A … :

Canon FC 2

Canon Pixma MP150 Error Code 5100
ANSWER : Make sure you check that a copy of Gustave Holst’s journey to the stars cassette isn’t stuck in there! haha. That’s what my error 5100 was all about, I was getting ready to dismantle the thing after threatening it with a water boarding.

Read Full Q/A … :

Canon FC 2