Canon FC 3
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Press and hold the “Power” button and reconnect the power cord. When the printer comes on, release the button. Wait five seconds and push the “Power” button again. This resets the printer`s internal memory and overrides the “Ink Absorber Full” error code.
When the message “Ink absorber full.” is displayed, the printer stops printing and needs ink absorber replacement. Push the power button to turn OFF the printer, and then contact the service center for replacement. Request either Canon or the dealer you purchased the machine for a repair service.
The bottom part of the printer Canon Pixma is fully covered with sponges and forms the so-called waste ink tank. Each time you clean the printheads on your inkjet printer, ink is sucked out of the printer`s print nozzles and out of the cartridges, and into the sponges on the bottom of the printer via one or more hoses.
The error “Ink Absorber Full” means that the internal ink absorber or flushing box will need to be replaced. The need to replace these items and the time period before replacement is dependent on the number of purges and flushes required to clean the ink system.
The purpose of the waste ink absorber is to safely collect any waste ink expelled during cleaning of the print head and borderless printing on photo printers. Over time this waste ink absorber can become full and will need to be replaced.
This error occurs due to the chip on your cartridge still reporting a low or empty ink level from its previous use. The chip itself cannot be reset, so when the cartridge is refilled and then installed into a new machine it will still register as empty.
You have the option of disposing of your existing cartridge and replacing it with a new one, but the far most cost-effective option is to empty this waste toner cartridge yourself. Below, we`re going to step you through how you can save on your printing expenses by handling this process yourself.
If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.
5B02 error – ink absorber full.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
replacing waste ink absorber on Canon Pixma ip6000
ANSWER : ditto, ditto & ditto
Canon iP1700 ink absorber reset and remove/clean
ANSWER : The 6 step directions about tank full error worked perfectly for me to correct the problem
Canon Pixma Pro 9000 Mark II ink dried in printer head.
ANSWER : This video shows how to remove the heads. Ignore his methods of cleaning them as they are really stupid. Best way to clean the heads is to run hot tap water into the screens and then flip it over and run the hot water on the heads. Repeat a few times until the water runs clear. Then dry it thoroughly with a paper towel and reinstall.
PRINTER MX 320 CANON ALL IN ONE PRINTER
ANSWER : Probably a worn feed roller. You can try cleaning it with a damp rag as it might just be covered with paper dust.
Canon pixma – ink absorber almost full
ANSWER : They are on the bottom of the printer. If you want to clean them, you can take them out and wash them in hot tap water. Wring them out like a sponge. You will need to reset the printer. http://jezpinions.blogspot.com/2012/03/canon-mg6150-ink-absorber-reset-error.html
Waste tank counter reset code for Canon printers.
ANSWER : I have a Canon Pixma MG4150 and I never see any references to it on help pages. I too want to get rid of the ink absorber warning after havig cleaned and reinstalled the absorber pads. Can anyone help?
Canon Printer does not print blue ink
ANSWER : I was also facing same issue with my printer. I tried a lot to fix that however I was not able to fix that. I got this link http://www.printer-techsupport.com/Canon-printer-support.htmlover the internet. I just visited and made a call on their toll free and got instant help for my printer.
Trying to reset Canon MP280's waste absorber
ANSWER : SSSSS