Canon FC 2

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If the paper feed rollers are dirty or have paper dust on them, the paper may not be fed properly. When this happens, you`ll need to clean the rollers twice: once with paper loaded, and once without.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
Partial prints are a common issue with printers and there are several main reasons it can occur: Problem with the print spooler (on Windows PCs) Overload of the GPU on later model Macs. Dodgy USB cord.
The paper has holes along both sides that fit over the sprockets located on the feeder wheel. When the wheel turns, it feeds the paper into the printer. The holes are torn off the paper after the printout is complete. And, yes, printers still use this type of feeder mechanism.
The print side or shiny side of the paper is not loaded face down in the tray. The paper width guides are too tight against the paper stack. The paper feed rollers are coated with dust. Debris such an as paper clips or bits of paper might have fallen into the paper path.
Check the nozzle check pattern you printed. (1) If lines of this pattern are missing, the print head nozzles need cleaning. (2) If these patterns have white streaks, the print head nozzles need cleaning.
Ink or toner cartridges that have become dislodged from their proper place. The wrong paper size loaded in the input tray. Clogged printer head nozzles causing a build-up of blocked ink or toner. Blank pages in the document you`re printing.
Check Paper Tray and Printer Connection

Verify your printer`s ink levels, clean the printhead, fill the paper tray, and avoid using substandard paper. Low-quality paper can cause “Ghost Paper Jams” and other issues that stop your printer from printing documents.

The photo tray is overloaded. The paper is curled. The print side, or shiny side, of the paper is not loaded in the tray face down. The paper width guide is too tight against the paper stack.
Lightly dampen a clean, lint-free cloth with bottled or distilled water, and then squeeze any excess liquid from the cloth. Press the cloth against the rollers and rotate them upwards with your fingers.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

Canon FC 2

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :

Canon FC 2

Canon MP110 won't print, paper won't feed
ANSWER : Thanks everyone!!!! My printer was working fine yesterday and then at night it would not print. Got very frustrated. It would say load paper but there was paper. Then it would only take one side of the paper and say paper jam and there was no jam. Today I landed on this page after searching online and I shook my printer.. Yes!!!!! and now it prints… You cannot imagine how happy I am… Doing the happy dance now!!!! Thanks everyone 🙂

Read Full Q/A … :

Canon FC 2

Canon mx410 Paper jam message, but no paper jam?!
ANSWER : I have exactly the same problem, no answers 😳

Read Full Q/A … :

Canon FC 2

Paper feed
ANSWER : Most times this is caused by a piece of torn paper that is lodged in the paper path.

Read Full Q/A … :

Canon FC 2

Paper feed problem
ANSWER : Those printers are really hard t.o take apart. As you can see, there are very few screws holding it together. All the panels snap on and aren’t meant to come back off for repair. What I do is gently pry around the panel with a small flat blade screwdriver until it pops up. There aren’t any manuals, so that’s pretty much the only way to do it. I’m pretty good at putting parts like that back in without disassembly. I’ve innovated different repair methods where I do the equivalent of laproscopic surgery with minimum disassembly. Maybe use a needle nosed pliers and a small screwdriver to help guide it in? I don’t know exactly where it came out of or how much access room you have.

Read Full Q/A … :

Canon FC 2

paper drive wont accept paper
ANSWER : There is probably a small scrap of paper stuck at the left edge of the paper path. The paper hits it and skews to the left. The smaller size bypasses it. You need to shove something stiff, like a piece of file folder, down the paper path and attempt to dislodge it.

Read Full Q/A … :

Canon FC 2

canon mp780 paper jam
ANSWER : Hey thanks a lot for the marvelous blog post for Canon printer. To get resolutions for all your problems contact us at our toll free number Canon Printer Help Desk Number UK 0800-098-8356.

Read Full Q/A … :

Canon FC 2