Canon FC 3
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Restart your computer – this often will recover any lost connections with wireless devices. Power off and on the printer, and even the access point or wireless router your printer connects to. Check your printer configuration – you may not be assigned to the correct port for the printer.
Three flashes: Paper jam
The paper may be jammed. Remove the jammed paper, reload paper properly in the printer, and then press the RESUME/CANCEL button.
This error will occur due to the paper jam inside your printer To fix the error code e03 on your printer, follow the below steps. Start by turning off your Canon Printer TS3122 printer and unplugging the power cord. Now, open the front cover of the printer. Now, slowly pull out the jammed paper inside the printer.
Unplug the printer and then reconnect the printer to reset the power module. Disconnect the power cord from the printer. Remove the battery from the printer. Unplug the power cord from the wall outlet, power strip, or surge protector.
2. Unplug and restart your printer. Sometimes power-cycling your printer can resolve the issue. Turn off your printer and unplug it, wait 30 seconds, plug your printer back in, and then turn the printer back on.
Three flashes:Front Tray is closed/Paper is loaded into the Manual Feed Slot of the Front Tray/Paper jams. If the Front Tray is closed, open it. The printer resumes printing.
Appropriate ink cartridge is not installed. Ink absorber is almost full. The protective material for the FINE cartridge or the tape remains attached. The media type and paper size are not set correctly.
Simply plug the USB cable from your printer into an available USB port on your PC, and turn the printer on. On the taskbar, select the Search icon, type Printers in the search bar, and then select Printers & scanners from the search results to open the Printers & scanners system setting.
Press the key on the printer`s control panel. If the printer has entered Sleep Mode 2, you can release the mode when [ ] (Power) is pressed.
Simply turn the printer off with the power button on the printer. Once turned off, disconnect the printer`s power cord from the back of the printer. Wait approximately 30 seconds before you reconnect it. Once reconnected, use the printer`s power button to turn the printer back on.
Simply turn the printer off with the power button on the printer. Once turned off, disconnect the printer`s power cord from the back of the printer. Wait approximately 30 seconds before you reconnect it. Once reconnected, use the printer`s power button to turn the printer back on.
Hold the on/off button and press the stop button 5 times. Release the on/off button. The printer resets itself and restarts automatically afterwards.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Canon MP600 died
ANSWER : hey guys I found this on the net check it out maybe somebody can make something out of it cuase they omitted this part on the service manual that I attained cause I have the same problem hope this helps.
Read Full Q/A … :
Canon FC 3
Canon MP530 – 6A00 Purge Unit?
ANSWER : I just took apart my MP530 which produces the 6A00 error, and cleand the wiping pads, rubber blades and everything I could reach from the purge unit. I also cleaned the print head. The waste ink level in the EEPROM is 66%.
Read Full Q/A … :
Canon FC 3
Canon Pixma MP150 Error Code 5100
ANSWER : Make sure you check that a copy of Gustave Holst’s journey to the stars cassette isn’t stuck in there! haha. That’s what my error 5100 was all about, I was getting ready to dismantle the thing after threatening it with a water boarding.
Read Full Q/A … :
Canon FC 3
Canon MX922 printer with B200 service code
ANSWER : Try green copy button and red triangle in a circle together while releasing the power button upon restarting printer.
Read Full Q/A … :
Canon FC 3
Canon Printer reset tool for MP100 MP400 series
ANSWER : Thanks a million for this. I have just managed to get my MP460 Ink levels reset having tried lots of other sites and failed.
Read Full Q/A … :
Canon FC 3
Canon i560 Will not print black
ANSWER : Dang, it worked for me then wentback to normal (not working) after the test page. Oh well not bad for a 10 year old bubble jet.
Read Full Q/A … :
Canon FC 3
Canon Pixma iP3000 "Open door" Error code.
ANSWER : Look for a protruding plastic on the top that goes into an indentation. Mine was in the front left side. Put a piece of cardboard into the indentation.and close the door. The top plastic piece is not pushing the door close sensor down and because its too short and the cardboard allows the sensor to be reached and pushed.
Read Full Q/A … :
Canon FC 3
Full Ink Tank in Canon Pixma ip4000
ANSWER : It had been exactly the same subject, could not find an appropriate broker and process for earnings finally had to rummage through the Web, and there I came across this page http://optioninvest.org .Possibly you’ll find there is a therapy to your condition, thanks for the fascination!))
Read Full Q/A … :
Canon FC 3