Canon FC 2
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
E, 1, 6 (LED display) The ink has run out. Replace the ink cartridge and close the paper output cover.
Canon printer error: “Error e02”
Error code e02 occurs due to overheating of the printhead or when the paper is not correctly placed into the input tray and therefore the paper feed rollers are unable to pick up the paper from the paper tray.
Turn the printer and camera power off, then turn on again. If the error message does not clear, contact a Canon Customer Support center for assistance. Close the cartridge cover. If the error message does not clear, turn the power off and on again.
Canon printers produce error codes for one of several reasons: The settings for your printer might not be compatible with the document you`re trying to print. The loading bay for your paper might have become lodged with paper or you`re using the wrong type of paper.
The E1 error code is an AUTO-STOP PROTECTION indicating a short or open circuit in the indoor pipe sensor. Try unplugging the unit and waiting 2 minutes for the power to discharge. Then plug the unit back in.
Typically, the E1 Error Code means that your boiler is running low on pressure, which is the cause of the boiler locking out and not working. When you see this code being displayed, all you have to do to fix it and get things back to normal is to repressurise your boiler.
I will be glad to help. An E2 error occurs when the printer attempts to print a single-page or multi-page print job, and the paper length selected in the print settings does not match the length of the loaded paper.
Whirlpool gold series dishwasher error code e2/ f2, means main control board is not getting correct signal from the user interface. Turn off power/breaker, remove screws holding inner door liner, remove liner and check/secure/clean all wire connections from front interface and main control board.
The E07 error message appears when your Canon Pixma printer detects that the “FINE Cartridge is not installed in the correct position”. A `FINE` cartridge refers to a stand alone black or tri-colour cartridge (with a printhead attached) that is used exclusively in two cartridge printers.
#751. The server is not functioning. The network is not connected. (The server may be unable to connect to the network, or it may have lost the connection.)
the printer is out of paper load the paper or remove the paper and reload it. again flip through the papers before loading the sheets into the printer to make sure that they are not sticking to each other align the edges of the sheets before loading them into the paper cassette.
In this induction we see E1 Error because of induction. sense input voltage low than normal.
This issue is typically caused by a setting conflict on your router. Please complete the following to troubleshoot this issue: 1. Turn off the machine, wait 30 seconds, and turn the machine back on.
F7 E1 Code in display:
This code indicates a motor speed sensing error, the motor can not achieve the correct speed for the cycle selection.
2022. When the Washing Machine is displaying E1 in the panel, it is indicating an error in the water supply. The appliance is not detecting that the unit is filling with water. To resolve, checking the following: • Check whether the water supply is turned on and that there is adequate water pressure.
This error generally indicates that a file or path is not able to be accessed by the user because of security settings.
This issue is typically caused by a setting conflict on your router. Please complete the following to troubleshoot this issue: 1. Turn off the machine, wait 30 seconds, and turn the machine back on.
This means there may have been a problem installing the update.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
ERROR On New Canon iR Advance C2030
ANSWER : Error E020-060 was solved by changing the new memory chip with an old one. It worked very well.
Read Full Q/A … :
Canon FC 2
Canon Pixma MX870, Error 6000 and Service Manual
ANSWER : Brand new MX922. Printed a couple of pics and now the 6000 error. Can’t see any obstruction. Could you provide the manual for dismantling the unit further? Or pointers for getting further into the box than just looking through the little folding inkwell door?
Read Full Q/A … :
Canon FC 2
CANON P200- ERROR 5100 PLEASE HELP!
ANSWER : Read this for solutions http://www.mytechtime.com/2011/10/canon-error-5100-how-to-fix.html
Read Full Q/A … :
Canon FC 2
Canon Pixma iP3000 "Open door" Error code.
ANSWER : Look for a protruding plastic on the top that goes into an indentation. Mine was in the front left side. Put a piece of cardboard into the indentation.and close the door. The top plastic piece is not pushing the door close sensor down and because its too short and the cardboard allows the sensor to be reached and pushed.
Read Full Q/A … :
Canon FC 2
Canon MP530 – Head Alignment Error
ANSWER : Hi Trigger, can you please let me know how this was resolved as I have a similar problem.
Read Full Q/A … :
Canon FC 2
Canon BJC-70 error message F 12
ANSWER : I am having the same problem, not only with my BJC-70, but also the equivalent problem with my BJC-80. Typically I am working at my computer, and the printer is powered up, but idle. All of a sudden for no apparent reason, it emits a series of beeps and returns the print head to the central position. The BJC-70 display Error F12. With the BJC80 you have to count the beeps. The problem seems to be caused by some sort of premature failure of the print head, due to an electronic fault. Sometimes, if the printer is powered down for a few minutes or longer, it will work normally for a short time after power is re-applied, but typically the problem recurs within 30 minutes, and this period of trouble free operation gradually reduces, until the print head will not work at all. The only solution is to replace the offending print head. You should, however, retain the failed head, in order to salvage any un-used ink remaining in the tanks. The new print head comes with full ink tanks. As soon as one of these fails, I replace it with an ink tank retrieved from the failed head. I don’t discard the failed head until both ink tanks have been retrieved.
Read Full Q/A … :
Canon FC 2
Canon Pixma MP150 Error Code 5100
ANSWER : Make sure you check that a copy of Gustave Holst’s journey to the stars cassette isn’t stuck in there! haha. That’s what my error 5100 was all about, I was getting ready to dismantle the thing after threatening it with a water boarding.
Read Full Q/A … :
Canon FC 2
canon MX700 6A80 error, head locked
ANSWER : I bought a canon pixma 7240 but on my first use I turn it on and the power lamp and error lamp blink alternatively the print head is stuck not moving please help I can’t even put the cartridges. My email [email protected] phone number 0719013770.
Read Full Q/A … :
Canon FC 2