Epson Stylus Photo RX520
Hi everyone!
Experienced technical support provide their insights in answering this question :
Epson printers don’t like to sit unused. The printheads will clog with dried ink. Your only hope is to use a Printhead cleaning kit. The Printer’s built in cleaner uses wet ink to flush dried up ink. Yeah, that works real good. Here’s a good source for the kit. http://www.printheadcleaningkit.com/kits.html
How to Identify and Fix Common printer Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
The Cause of Clogs
Printheads clog because nozzles get blocked by either air or ink. Clogs usually happen when: You keep printing with depleted ink cartridges. Using empty ink cartridges can result in air bubbles that can clog your cartridge and/or printhead.
1 Open the paper support and pull up its extensions. 2 Open the output tray and pull out its extension. 3 Press in the release button and slide the edge guide to the left. 4 Load paper against the right edge guide and behind the tab.
If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.
If paper dust builds up on the rollers, they may lose traction and become unable to feed paper properly. Clean the paper guide. If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary. Then reload the paper.
There are a number of reasons why this might happen. In a large number of cases we come across, the photo paper weight (which is measured in GSM) or overall thickness exceeds the printer`s ability meaning it is too think or too heavy for the rollers to successfully handle.
The common reasons for this issue are various, for instance, the paper input tray is overloaded, dust or moisture can affect the paper feed or paper pick rollers, the printer driver is old, etc. Thus, the printer cannot detect the paper that has been inserted into the tray.
There are a few things that could be the cause of this problem, including: Empty ink or toner cartridges that need replacing. Ink or toner cartridges that have become dislodged from their proper place. The wrong paper size loaded in the input tray.
As a rule of thumb, to achieve photo quality print, you will need to use an image resolution of 300 pixels per inch. We write this as 300 DPI and means that in each inch of your print there will be 300 pixels.
Several factors may cause the product to print blank pages, such as print settings, low ink, or the product itself. Check the following: Make sure the product is placed on a flat, stable surface that extends beyond the base in all directions. The product won`t operate properly if it`s tilted or at an angle.
Ensure that the supported settings are applied in the printer driver and click Print in Black to continue printing using Black Print Mode or Cancel Print to replace the expended cartridge.
Press the home button, if necessary. Press the left or right arrow button to select Maintenance > Reset Ink Level. Press the start button, the OK button twice, and then the start button again. Press the right or left arrow button to highlight the ink tank you refilled and press the OK button to select it.
Ensure that the supported settings are applied in the printer driver and click Print in Black to continue printing using Black Print Mode or Cancel Print to replace the expended cartridge.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Prints blank pages, won't print from computer
ANSWER : Don’t know why you replaced the fuser, but assuming you had print before, then it must have been something you did during the procedure. Only thing I can suggest is to recheck your work. Just because you reinstalled a connector doesn’t mean that it is seated firmly enough to work. Any flat ribbon connectors that you removed and reinstalled, check to see that the contacts are all flat and not peeled back.
Read Full Q/A … :
Epson Stylus Photo RX520
when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?
Read Full Q/A … :
Epson Stylus Photo RX520
cannot print
ANSWER : Epson printers don’t like to sit unused. The printheads will clog with dried ink. Your only hope is to use a Printhead cleaning kit. The Printer’s built in cleaner uses wet ink to flush dried up ink. Yeah, that works real good. Here’s a good source for the kit. http://www.printheadcleaningkit.com/kits.html
Read Full Q/A … :
Epson Stylus Photo RX520
Print file sent but no printing occurs
ANSWER : Been working on these since they first were released. Never seen a problem like yours. If it happens again, try doing an engine test, as it bypasses the formatter board. The engine test is located at the right side of the manual tray opening. Look for a hole in the side wall. Stick something like a paper clip into it to actuate the test button. It will then print a lined test page. If it does that, then it points to the formatter board as the cause of your problem.
Read Full Q/A … :
Epson Stylus Photo RX520
My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.
Read Full Q/A … :
Epson Stylus Photo RX520
HP Deskjet 640c wont print??
ANSWER : yes
Read Full Q/A … :
Epson Stylus Photo RX520
Epson Artisan 835 print head cleaning question
ANSWER : I had the same problem. After reading the comments, I tried Liquid Wrench spray. 1st try got about sixty percent improvement. Tried again this time I let it set for about 10 min then did a head cleaning. Completely solved the problem. I am a little concerned about its use on plastic. So far so good.
Read Full Q/A … :
Epson Stylus Photo RX520
My printing come out blurred
ANSWER : doris…There are usually 2 reasons for blurry output on this printer. First, make sure that the alignment is correct. You can get to it from the maintenance tab on the software that came with the printer. The other common cause of blurring is debris under the printhead. Hope this helps.
Read Full Q/A … :
Epson Stylus Photo RX520