Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Canon printers produce error codes for one of several reasons: The settings for your printer might not be compatible with the document you`re trying to print. The loading bay for your paper might have become lodged with paper or you`re using the wrong type of paper.
E38. – Cannot connect to a wireless router. Cannot change the LAN settings. Press the printer`s Black or Color button to resolve the error.
My PIXMA MG5320 has error U052-`the type of print head is incorrect. Install the correct print head.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed. SUBSCRIBE RSS FEEDS.
E, 0, 8 E08 Ink absorber is almost full. The ink absorber collects excess ink after head cleaning or during printing. Ink usually goes into a bottle which eventually becomes full. There is a risk that ink can begin to spill.
Open Settings -> Devices -> Printers and Scanners (or run a quick access URI command: ms-settings:printers ); Select a printer you want to remove and click Remove Device; Confirm the printer removal.
If the orange light is lit and the E03 support code displays on your printer, there is a paper jam.
The mistake code 5800 methods the waste ink counter reset (yellowish and orange 1/3 Page 2 light, blazing on the other hand a few times). Group printers typically need re-setter to re establish the atmosphere to your underlying. Conventional printer must be flashed following completing a huge amount of print movement.
Description. The error U051 / U052 indicates that a communication issue with the print head has occurred. This can be caused either by the print head not being installed properly or a hardware failure.
When the message “U052 The type of print head is incorrect. Install the correct print head.” is displayed, follow the steps below to install the print head again: If you still have the trouble, contact the repair service.
Use the Easy-Scroll Wheel or the right / left arrow to select [Settings], then press the <OK> button. Use the Easy-Scroll Wheel or the right / left arrow to select [Device settings], then press the <OK> button. Use the Easy-Scroll Wheel or the up / down arrow to select [Reset settings], then press the <OK> button.
1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.
Canon printer error: “Error e02”

Error code e02 occurs due to overheating of the printhead or when the paper is not correctly placed into the input tray and therefore the paper feed rollers are unable to pick up the paper from the paper tray.

To remove printer and driver on Windows 10, open Settings > Printers & scanners, select the printer, and click “Remove device.” Then open Print management > Custom Filters > All Drivers, right-click the driver, and select “Delete.”
A mechanical error occurs when a car`s ability to perform as intended leads to a motor vehicle accident. When diagnosing a car accident, it`s essential to consider whether the mechanical failure was a result of improper part installation, the use of faulty parts, or due to a manufacturing defect.
Once the printer believes the cartridge has run out of ink you will be presented with either the E13 message or the E16 message that indicates that you need to change the ink cartridge. If this message is being displayed on your printers screen then your printer will stop printing and scanning.
The Canon E08 error message indicates that the “Ink absorber is almost full” in the bottom of your printer. To bypass this message you can simply press the black or colour button of your printer which will allow you to continue printing.
According to Canon, Error 06 indicates a fault of the sensor cleaning module.
The 6C10 error has been variously described as both a “Reset Canon Printer ink absorber” error or a “Valve Cam Sensor” error.
Support Code=2500

Print head nozzles are clogged. The paper of size other than A4 or Letter is loaded in the cassette 2.

Media type and paper size are not set correctly. Press the printer`s Stop button to cancel printing, change the media type or paper size setting, and then redo the printing.
If you are getting a B504 error, it would point to a problem with the ink loaded in the printer or a problem with the hardware. In this situation, you can try unplugging the printer from the power and then pressing the power button 10 times while the printer is unplugged.
If you are and the issue remains, then the next common reason is a paper jam has resulted in a piece of paper being stuck inside. Check the rear door and inside the front door for any paper fragments and remove. 3. If you are and the issue remains, then clean the printer`s encoder strip.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

error message
ANSWER : Search it on google

Read Full Q/A … :
Unknown Printer

paper jam error pixma mp150
ANSWER : Cereal box trick worked on my Canon MG-2922. Found McDonald’s Monopoly pieces. No winners though. Thanks for the idea… saved some $.

Read Full Q/A … :
Unknown Printer

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :
Unknown Printer

message error: ADF paper jam
ANSWER : There is a thin plastic arm that the paper pushes on. It is spring loaded. If it doesn’t return and unblock the sensor after the paper passes it, you get the paper jam warning. I’m guessing that is the spring you are referring to.

Read Full Q/A … :
Unknown Printer

Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.

Read Full Q/A … :
Unknown Printer

Canon Pixma iP3000 "Open door" Error code.
ANSWER : Look for a protruding plastic on the top that goes into an indentation. Mine was in the front left side. Put a piece of cardboard into the indentation.and close the door. The top plastic piece is not pushing the door close sensor down and because its too short and the cardboard allows the sensor to be reached and pushed.

Read Full Q/A … :
Unknown Printer

Error B200
ANSWER : Hi Ladybyrd

Read Full Q/A … :
Unknown Printer

Canon Pixma MP150 Error Code 5100
ANSWER : Make sure you check that a copy of Gustave Holst’s journey to the stars cassette isn’t stuck in there! haha. That’s what my error 5100 was all about, I was getting ready to dismantle the thing after threatening it with a water boarding.

Read Full Q/A … :
Unknown Printer