Brother MFC 9440CN

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If you can not pull out the jammed paper, lift the scanner cover from the right-hand side of the machine until it locks securely into the open position. Check inside the machine. Lift the scanner cover to the open position until it locks securely into the open position. Check the print head`s position.
Sometimes a paper jam error persists even though there is no jammed paper (false paper jam). Reset the printer, which might clear a false paper jam error, and then try to print again. With the printer turned on, disconnect the power cord from the printer. Unplug the power cord from the power source.
You may be putting too much paper into the paper tray. It should never be overfilled as it can often cause a jam. If you only put the amount of paper you`re going to use for one printing task, you`re less likely to suffer a jam. Also, make sure the paper fits the tray and that it`s inserted correctly.
Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer. False paper jams can also occur.
During a print job, the printer stops feeding pages, and a Paper Jam error message displays on the printer control panel. This indicates that paper might be jammed inside the printer. note: Paper jams can be real or false. The printer might report a paper jam even when there is no jammed paper.
Did you know most copier paper jams are caused by the paper itself? Misaligned paper. When a stack of paper isn`t aligned properly in the machine, it often causes a paper jam issue. When adding a ream of paper, always fan the paper, load carefully and avoid overstuffing the tray.
Open the back cover (face-up output tray). Pull down the tabs at the left and right hand sides to open the fuser cover (1). Using both hands, gently pull the jammed paper out of the fuser unit. Close the fuser cover (1) and the back cover (face-up output tray).
Paper Jam was developed by AlphaDream while Intelligent Systems oversaw production. The concept of a crossover came to be when AlphaDream conceptualized a third character for the player to control in-game to help shake up the traditional gameplay of the series.
Pick up the front of the tray, pull it out slightly, and lower the tray back down so it is level. Pull the right side of paper tray out. Move the paper tray to the right and take the tray out of the machine.
The guides in the paper tray are there to make sure the stack of paper is exactly where the printer was designed to grab from. If the paper is even slightly askew, the rollers will pick it up a little crooked, and — guess what — the crooked sheet will immediately get jammed.
Hold the printer with one hand and hold the paper tray with the other hand. Push or pull the paper tray sideways while holding the printer still.
Cause 1: The photo bypass tray is located at the wrong position. Cause 4: Paper dust has accumulated on the surface of the paper pick-up rollers. Cause 6: The paper tray was not fully inserted. NOTE: Illustrations shown below are from a representative product and may differ from your Brother machine.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

paper jams tray 1
ANSWER : Often there have been issues with the broker. Not merely throwing and robbed, and I determined to have established brokers with site http://put-call-options.com which is recommended just luchishh. Who I have previously been working with an extra half a year. Thank you for attention.))

Read Full Q/A … :

Brother MFC 9440CN

MFC 8440 Brother 5 in 1
ANSWER : I have the same problem except both left and right hinges are broke. I’ve removed the and it does work but I’d still like to order the parts and replace them. Where would I find the parts for ordering.

Read Full Q/A … :

Brother MFC 9440CN

Brother MFC-J6510DW extra paper tray.
ANSWER : There clearly was a similar problem couldn’t enter in to a ditch of benefit drawing up a strategy. A pal gave this http://put-call-options.com site to select an appropriate technique and I have chosen for themselves the optimum and successful naybolee. I hope I served you with your problem. Thanks for attention)))

Read Full Q/A … :

Brother MFC 9440CN

Paper Jam Tray 1
ANSWER : Tray No. 1 (the feeder) has to be either FULLY closed or FULLY down, down to about a 45 degree angle. Then hit the OK button and it should Initialize and start working. This solution is for when there is actually NO paper jamming the printer.

Read Full Q/A … :

Brother MFC 9440CN

Brother HL-2170W — 2nd sheet printing causes jam
ANSWER : I tried Angry Larry’s link to Photobucket but there’s an error message. I tried rocklobster’s link to Imageshack, but it’s for a different printer. Can someone please send me the photos to fix this issue with my Brother HL-2170W? My email is [email protected] Very much appreciated!

Read Full Q/A … :

Brother MFC 9440CN

Tray 1 (upper tray) paper feed problem
ANSWER : There is no way of adjusting the distance of lift. Could be that the pickup roller is worn enough that it will pick up a sheet that is higher, but not one that is lower down. You can look at the end of the roller that first makes contact and see if it is worn smooth.

Read Full Q/A … :

Brother MFC 9440CN

Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :

Brother MFC 9440CN

Brother Hl-2040 paper over feed
ANSWER : Your instructions saved me..I had the board off 3 times before i saw your pix….thanks so much!

Read Full Q/A … :

Brother MFC 9440CN